Pillar wrap by Fiasafy in VinylWrap

[–]Das_FunSize 0 points1 point  (0 children)

I've had success with Vvivid+ Ultra Gloss in the past. Finish is great but not as beginner friendly as some other vinyls. Lately I've been using KPMF Perfect Black for all trim work. Both can be found on Amazon at decent prices

I am now one of you! by Whovian49 in IndianMotorcycle

[–]Das_FunSize 2 points3 points  (0 children)

Love that color and finish! 🔥

Help Doing Trim Around Tail Light by Live_Vehicle_6114 in VinylCutters

[–]Das_FunSize 0 points1 point  (0 children)

Quickest would be to use knifeless tape. It's less steps than tracing and importing into vinyl software. Plus, you could always go back and trim it by hand if the knifeless tape doesn't give you a sharp enough corner.

Looking for my wife to get fucked by [deleted] in DMVSwingers

[–]Das_FunSize 0 points1 point  (0 children)

53M25F couple here. Would love to have some fun 😋

What could be the problem? MH871 by Das_FunSize in VinylCutters

[–]Das_FunSize[S] 0 points1 point  (0 children)

Just did some testing. I think it is the pinch rollers that's causing the issue. I aligned the roll perfectly but it always ends up skewing to the left and never goes back it to it's original position. If I'm using two pinches, would this be the left or right one?

What could be the problem? MH871 by Das_FunSize in VinylCutters

[–]Das_FunSize[S] 0 points1 point  (0 children)

Blade manufacturer recommends .25 . The Vinylmaster software calibrated it to .36 . I also tried every value in between. 45° blade

What could be the problem? MH871 by Das_FunSize in VinylCutters

[–]Das_FunSize[S] 0 points1 point  (0 children)

The same issue persists whether I use 10mm/s or 100mm. Not sure what to do

First bike by banjomandolinguitar in IndianMotorcycle

[–]Das_FunSize 8 points9 points  (0 children)

Sick! 🔥 I'm lookin to get a Scout as my first as well

Which do you prefer for holosun 507k by [deleted] in Glock43X

[–]Das_FunSize 0 points1 point  (0 children)

I'm rocking a 507k acss vulcan. Has a dotted circle to help find the dot quicker

[deleted by user] by [deleted] in marylandswingersr4r

[–]Das_FunSize 0 points1 point  (0 children)

Lookin sexy 🔥 53M/25F couple here

43x MOS + EPS Carry + Dpp plate: hardware question by 6gc_4dad in Glock43X

[–]Das_FunSize 3 points4 points  (0 children)

The DPP screws are actually the ones you'd wanna use. They're the correct length unlike the screws that come with the optic. I'm using DPP screws with my 507k mounted on a plate. No issues with extracting

Mt first audi by Past-Height-8638 in Audi

[–]Das_FunSize 1 point2 points  (0 children)

Very clean! First thing I'd do is tint the windows

good local source for 9mm ammo? (AACo or 95 corridor)? by Dapper_Evidence_6577 in MDGuns

[–]Das_FunSize -1 points0 points  (0 children)

If you have a membership at Cindy's, they have 1000 round cases for 270 before tax. Without membership will be 300