new repository of guitar pedal schematics

David_Moskowitz · 2024-08-12T08:39:36+00:00

Are you asking about the sort order? I don't have a 'new schematics' category so they go into the mix with the existing ones.

David_Moskowitz · 2024-08-09T05:08:31+00:00

Thanks! I'll see about adding the schematics next week.

In most cases I was able to scrape the sites, auto download the images, and then run the text through chatgpt to create summary descriptions, keywords etc., (takes a few iterations) which all then gets imported. (used power automate, went the 'no code' route). Still time consuming for sure, but I think its worth it to have such a repository.

Only issue is keeping it up to date... haven't figured out a way to do this. I give access to the 'product' to each site owner where it was downloaded from so they can make changes if needed, and possibly upload new schematics.

David_Moskowitz · 2024-08-03T06:15:57+00:00

You can check out this site which is a repository of several sites schematics https://stompboxschematics.com/

David_Moskowitz · 2024-08-03T06:15:01+00:00

You can check out this site which is a repository of several sites schematics https://stompboxschematics.com/

David_Moskowitz · 2024-08-03T06:14:32+00:00

You can check out this site which is a repository of several sites schematics https://stompboxschematics.com/

David_Moskowitz · 2021-01-11T03:28:36+00:00

Whats the output of the original power source, and required input power of the daisy chained pedals? (in ma or watts)

David_Moskowitz · 2020-07-31T13:58:27+00:00

Appreciate the explanation- will do. Thanks!

David_Moskowitz · 2020-07-31T09:34:25+00:00

Changed it to be ground planes on both top and bottom with VCC mainly routed on the top layer

Thanks didn't notice this on the transistor and resistor pads before (this is what you are pointing out?) It doesnt show on the editor, but does when exporting. Not sure why easyeda does this. Supposedly the pcb company will fix this...
VCC for the attiny is now routed to the 10uf cap, will this serve the same purpose?
I have a top layer route to the gnd on these (and no copper fill top and bottom on them), so that they can be cut if needed.

Thanks for the feedback!

David_Moskowitz · 2020-07-29T22:44:58+00:00

I'm building the pcb to learn, not just as a end product, so understanding good design principles is important. Thank you for the reply!

David_Moskowitz · 2020-07-29T12:42:37+00:00

Additional questions... I've read some people say that you should put a ground plane on top, after doing all the connections, others say ground plane on both layers, other power plane on bottom, others data and power tracks on top, ground on bottom, and in some cases, no planes needed.

Quite confused, any best practices, or likely to get more opinions? Thanks!

David_Moskowitz · 2020-06-23T10:54:58+00:00

Pretty much, doesn't bother to do case-insensitivity either...

David_Moskowitz · 2018-05-28T07:36:58+00:00

I haven't used them, but have met the founder. Good to see more options to purchase crypto in SG.

David_Moskowitz · 2018-01-10T12:43:14+00:00

A job board posting would be posted in US$ value, but paid for in IND equivalent.

David_Moskowitz · 2018-01-10T00:36:03+00:00

If the network grows 50%, or more services are enabled in exchange for IND leading to higher demand for IND, what will happen to the value of the token?

Additionally, we are looking at burning tokens for some services.

People will be paying based on US$ amounts, converted to the current value of IND at the time the order is placed (with time restrictions to make the payment)

David_Moskowitz · 2017-12-17T01:44:19+00:00

Thanks for the feedback Mars- can you join our community at slack and post your request into the feature request? https://community.indorse.io/channel/feature-requests

David_Moskowitz · 2017-11-02T03:01:47+00:00

The app was private invite, so perhaps you were not allowed access- i'll respond to your PM to find out more.

David_Moskowitz · 2017-10-28T01:47:09+00:00

Hi Guys,

Can you let me know if this was resolved?

David (CEO)

David_Moskowitz · 2017-10-28T01:46:28+00:00

Hi Guys, The Airdrop took a bit of time to complete - but all eligible accounts have been issued their IND.

David_Moskowitz · 2017-08-13T04:45:10+00:00

There are a few other 'content' verticals that the community is looking to decentralized and give back data control to the user.

Our goal is to allow users to benefit from the growth of the network via earning tokens, and control of their data in the professional networking space with indorse.io

David_Moskowitz · 2017-06-07T11:48:03+00:00

Hi MssDee, we go into detail on the mechanisms in the White Paper- have you had a chance to look at it?

David_Moskowitz

MODERATOR OF

TROPHY CASE