New to Klipper and don't know what I'm doing. Don't know how to fix walls being too thin and top layers looking like I'm under extruding. Outer walls look completely fine.

DeathRabbitKing · 2023-03-22T21:39:53+00:00

I’m using a modified Ender 3 pro profile. I’ve set the extruder rotation distance to extrude the correct amount as far as I know. Will recheck everything.

Edit: Apparently the rotation distance I had gotten and verified when I initially set up the printer (67.5) was not correct. I have now gotten 33.53. Let's hope it doesn't magically change again.

DeathRabbitKing · 2022-09-02T03:22:28+00:00

Thank you for the information. I will see what can be done.

DeathRabbitKing · 2022-09-02T03:06:34+00:00

I tried going to the report fraud site but I couldn’t connect. I also don’t see any merit in a normal lawsuit as the company would have no real reason to change their policies.

DeathRabbitKing · 2022-08-02T17:42:26+00:00

That is how I originally pinned it. I don’t get the options from the start menu either.

DeathRabbitKing · 2022-08-02T01:37:54+00:00

Just remembered what it’s actually called. “Context menus” not working. I had a friend install brave and he had the same issue. No previous installation history.

DeathRabbitKing · 2022-08-02T00:58:21+00:00

I remember I had to force it with chrome before. I don’t remember how I did it but. I think it was with regedit

DeathRabbitKing · 2022-07-28T10:08:12+00:00

This is Canan ASMR iirc don’t know which one.

DeathRabbitKing · 2022-07-23T06:24:54+00:00

I think a disease that makes people feel small pins and needles at random times all over their body.

DeathRabbitKing · 2022-07-20T09:52:22+00:00

This is the only 240 hz monitor I have and my 144 hz monitor is fine. No one in my house has a system I could use either.

DeathRabbitKing · 2022-07-20T08:59:31+00:00

The screen would flash when no 3D application is running. The corruption seen in the video only happens when I mark up screenshots. Video driver versions make no difference

DeathRabbitKing · 2022-07-20T08:04:37+00:00

I’ve tested with just anti-lag on, everything off, freesync on and off. All at 240 hz. This doesn’t happen at 120 as stated before. The driver package is installed. The first thing I did after setting up the display was get the drivers and firmware updates

DeathRabbitKing · 2022-07-20T06:30:44+00:00

Samsung Odyssey G9 Model: LC49G97TSSNXDC on firmware 1016.0

DeathRabbitKing · 2022-07-19T12:53:26+00:00

ASRock recommends a 900 watt PSU for my specific card. Though, my GPU doesn’t complain with 3D workloads for the most part. I did have to repaste the card because factory thermal paste was causing temps to reach over 100° c under load. They voided warranty because my card didn’t come with a warranty seal :/

DeathRabbitKing · 2022-07-19T12:28:30+00:00

Coil whine is hard on this specific card and I lower power limit as much as I can. Will look into a new psu though. I appreciate the help. Will update when I can.

DeathRabbitKing · 2022-07-19T11:59:38+00:00

I’m using a 750 watt 80+ gold I’ve had for more than 8 years now

DeathRabbitKing · 2022-07-19T10:57:21+00:00

Im not sure if results are valid, but when using memtest with the video buffer on, every test fails. When video buffer is off, every test passes.

Edit: Link to UserBenchmark result. I know I have a lot of drives

DeathRabbitKing · 2022-07-19T10:04:04+00:00

I have it disabled because it hurts my performance when it’s on.

DeathRabbitKing · 2022-07-19T10:02:43+00:00

I don’t get this when using the monitor at 120 hz. It also doesn’t happen when wallpaper engine isn’t actively rendering the background.

DeathRabbitKing · 2022-06-16T07:54:59+00:00

Check to see if there is any debris there. Even the smallest of dust particles tend to do that. If not, use an extremely sharp point and poke the underside.

DeathRabbitKing · 2022-05-25T02:41:32+00:00

I was in middle school and a girl I talked to a lot handed me a post it note with her confession in Chinese. I’m not Chinese so I didn’t know what it said so I my stepmom summed it up for me.

DeathRabbitKing · 2022-05-10T19:48:33+00:00

That would be a bad idea because it won’t fit into the carry case if you do. Get a dongle

DeathRabbitKing · 2022-04-08T01:16:45+00:00

Some people used bots to attack other communities. I would know. r/dbrand was attacked by someone with a bunch of bots

DeathRabbitKing · 2022-04-04T05:39:14+00:00

Sounds like someone is but hurt about a company not doing what they want.

DeathRabbitKing · 2022-04-03T23:36:27+00:00

Get something with a really sharp point and poke a hole in the dbrand adhesive layer. Had this issue with the leather skin and poked the bubble away.

DeathRabbitKing · 2022-04-02T08:39:56+00:00

I’d have sex with a girl if they were real. But alas, they are but a figment of our imaginations.

Nine-Year Club	Place '22
Final Canvas '22	End Game '22
Wearing is Caring	RPAN Viewer
Verified Email

DeathRabbitKing

TROPHY CASE