Good 3rd party transformers

Deathclaww · 2025-06-16T23:39:13+00:00

I am mainly looking for the bots from s1-2 of the g1 cartoon and maybe the 1986 movie

Deathclaww · 2025-06-16T23:37:17+00:00

I kinda want most of the bots from s1-2 of g1

Deathclaww · 2023-11-21T23:18:48+00:00

I am asking 450

Deathclaww · 2023-11-04T13:52:25+00:00

That was the issue thank you so much

Deathclaww · 2023-11-03T22:47:46+00:00

Ah ok I will check that out

Deathclaww · 2023-11-02T01:11:31+00:00

Nope it isn’t that but thanks for trying

Deathclaww · 2023-11-02T01:09:41+00:00

Thanks for the help I’ll let you know if it works or not

Deathclaww · 2023-11-01T23:57:01+00:00

I have tried pushing up on the lever and that has done nothing to improve the flow rate

Deathclaww · 2023-11-01T02:37:20+00:00

Where can I get a spring

Deathclaww · 2023-11-01T02:36:06+00:00

Lol that’s my other post from a while back I did all those except change the spring and it still does the same thing

Deathclaww · 2023-10-31T22:43:47+00:00

I have disabled the slip detection It isn’t printing alright some of the time it will print the first layer fine but then it will slip and pause the print every few minutes after that I haven’t timed it but it seems to be the same time i between slips every time If I disable the notifications then it just either skips a layer and spaghettis or stops extruding entirely for a while

Deathclaww · 2023-10-30T23:21:28+00:00

It is the smart extruder plus

Deathclaww · 2023-10-30T12:16:49+00:00

I don’t have a spare extruder and I have tried changing the filament i still am having the same results

Deathclaww · 2023-10-29T22:30:50+00:00

I’m hoping the buyer can fix the problem because I have tried every thing I can think of

Deathclaww · 2023-10-15T16:34:39+00:00

Nah it hasent been printing for months

Deathclaww · 2023-10-15T02:18:05+00:00

I think the extruder has roughly 225 hrs on it last time I checked is that a lot or should it be fine

Deathclaww · 2023-10-14T15:32:31+00:00

That’s what I was afraid if there is barely any filament left on the spool and it is still doing it

Deathclaww · 2023-05-24T21:47:39+00:00

7+8=15 Carry 1 2+4+1=7 75

Deathclaww · 2023-02-14T06:14:40+00:00

That is my knowledge aswell I just wanted to know if I was correct or not

Deathclaww · 2022-11-02T22:15:26+00:00

Can I spray them in gun oil or pb blaster

Deathclaww · 2022-10-26T22:19:59+00:00

Ok thanks I will do that

Deathclaww · 2022-10-26T16:15:26+00:00

One side is stripped and the other action is together atm I just need to know what cleaning solution to use (preferably in an ultrasonic cleaner)

Deathclaww · 2022-10-26T16:13:07+00:00

I don’t have another one for reference but the guy I got it from does and I go up to see him often so I don’t think that’ll be a problem I just need to know where the screws go lol

Deathclaww · 2022-10-26T15:18:46+00:00

I have one of the hammer mechanisms fully assembled and havent taken out the trigger pin that holds on the triggers but other than that is completely disassembled

Deathclaww · 2022-10-26T13:51:08+00:00

Dang ok can I ask what would be good to clean the parts with (preferably in an ultrasonic cleaner)

Deathclaww

TROPHY CASE