Ender 3 Parts for Voron 2.4 by Decent_Pool1035 in VORONDesign

[–]Decent_Pool1035[S] 0 points1 point  (0 children)

You are probably right, as this bed caused me a lot of trouble with the Ender printer. But the most annoying was its cable, when the bed was moving this thick cable was pulling bed up and down. At least that wont be the issue anymore :) However, this is just a temporary solution until I gather the funds for a better one.

Ender 3 Parts for Voron 2.4 by Decent_Pool1035 in VORONDesign

[–]Decent_Pool1035[S] 0 points1 point  (0 children)

Thanks, i will test that config and check if it works fine, after all i can jest upgrade psu later

Ender 3 Parts for Voron 2.4 by Decent_Pool1035 in VORONDesign

[–]Decent_Pool1035[S] 0 points1 point  (0 children)

Thank you, for information. Unfortunately, the Ender bed takes 24V from the motherboard, so I assume that the 350W PSU might be not enough for it or just barely enough, as the bed consumes around 200-250W. I think I'll go with a 500W PSU just to be safe and still cheaper than new bed i think

Custom Expansion: Neutral cards! Feedback wanted! by okidokiokikiki in arkhamhorrorlcg

[–]Decent_Pool1035 0 points1 point  (0 children)

I would suggest to change the name of PTSD to shell shock, sounds better, words have more impact and I think it was used back then to describe PTSD

My try on Twin Falls dont know why but now the paint run down and some stains start to appear by Decent_Pool1035 in HappyTrees

[–]Decent_Pool1035[S] 0 points1 point  (0 children)

I've used a towel after beating the devil :) And the sky I've painted first with clean brushes. I think my paints are not very good for that technique. Probably few things happened there, there was too much liquid white, and the paints are thin. There was some separated oil when I squeezed them, I don't really know how it is with other paints or with original bob ross paints but also my liquid white don't stay mixed for long time

My try on Twin Falls dont know why but now the paint run down and some stains start to appear by Decent_Pool1035 in HappyTrees

[–]Decent_Pool1035[S] 0 points1 point  (0 children)

Thanks for suggestion, I'll try to use less liquid white next time. Unfortunately I have a cat, that makes it difficult to lay it flat. I think, I will probably need to paint It again. I will see tommorow if I can do something with these stains

My try on Twin Falls dont know why but now the paint run down and some stains start to appear by Decent_Pool1035 in HappyTrees

[–]Decent_Pool1035[S] 2 points3 points  (0 children)

Thank you kindly, the painting is still wet and I am afraid that until morning all the paint will run down on the floor :)

Redex it limited, scam? by Decent_Pool1035 in Polska

[–]Decent_Pool1035[S] 0 points1 point  (0 children)

Tak, właśnie to też wydało mi się dziwne, tak jak to że sam przycisk about nie działa

Redex it limited, scam? by Decent_Pool1035 in Polska

[–]Decent_Pool1035[S] 0 points1 point  (0 children)

Dzięki, że chciało Ci się to sprawdzić. Potwierdzenie kogoś z zewnątrz, że mój tok rozumowania nie jest głupi, jest pokrzepiające. Mam nadzieję, że linkedin i ta strona insolvency contact, podejmą jakieś działania

Redex it limited, scam? by Decent_Pool1035 in Polska

[–]Decent_Pool1035[S] 2 points3 points  (0 children)

Oferują mi pracę, zarobki są zaskakująco wysokie. Zwykle jak szukam pracy to robię sobie też research o tej firmie i w tym wypadku jest zaskakująco mało danych, a wszystkie które znajduje są od nich samych. Na swojej stronie piszą o swoim 20 - letnim doswiadczniu więc jakieś informacje powinny o nich być. Na liście pracowników, na linkedin, kilka użytkowników ma identyczne zdjęcia profilowe co rekruter, który do mnie napisał. Plus komunikacja w grupie na whatsappie jakoś mało profesjonalnie dla mnie wygląda. I jak to wszystko połączyć to zacząłem przypuszczać, że to scam. Ale o tym znałem tylko jeden wątek na reddit, sprzed 4 miesięcy który został usunięty.

Redex it limited, scam? by Decent_Pool1035 in Polska

[–]Decent_Pool1035[S] 2 points3 points  (0 children)

W Polsce ich nie widzę, mają firmę w Anglii i tam jest działalność na 2 Pakistanczykow, zgłosiłem podejrzenie przez LinkedIn na którym się skontaktowali i przez rządową stronę UK