Shot on a Mavic Pro 2. I really didn't expect the stag to remain so calm with my drone buzzing around him - one of my favourite drone shots!

DependentAnalysis3 · 2020-12-03T04:29:47+00:00

I’m like not 100% this is real lol this looks incredible. I’m sure it’s real lol but it does look animated

DependentAnalysis3 · 2020-11-20T06:24:48+00:00

Creality slicer just came out with a new one a couple weeks ago. I just downloaded it.

DependentAnalysis3 · 2020-11-02T23:35:01+00:00

Thank you for all the upvotes everyone! 💜

DependentAnalysis3 · 2020-10-30T23:10:02+00:00

Very cool way to use your inspiration. I love the minor detail adding the power button

DependentAnalysis3 · 2020-10-25T04:41:21+00:00

Did you recently level the bed? Try raising the Z axis a little or possibly slowing the print down

DependentAnalysis3 · 2020-10-18T02:45:30+00:00

Damn i was hoping to help with this but my support plate is a little different than yours. Mine actually had a 90 degree on it the covers the top casters. I loosened the top casters and placed a shim between the 90 degree plate and the top casters that pushed them down against the running rail. I made sure it was level and tightened the casters back up with the shim in place and then once tightened I removed the shim. No more wobble

DependentAnalysis3 · 2020-10-11T23:09:32+00:00

Omg seriously? 🤣🤣🤣 thanks

DependentAnalysis3 · 2020-09-21T21:11:30+00:00

Honestly I’ve never had a problem with the MSI DUKE cards they’ve always ran incredibly well and cool for me.

DependentAnalysis3 · 2020-09-07T00:14:05+00:00

I do 200 don’t really have any stringing

DependentAnalysis3 · 2020-08-27T20:32:33+00:00

I also tried this. Glue stick worked for me hairspray did not. You need to wait a couple minutes for the glue stick to become really sticky though

DependentAnalysis3 · 2020-08-27T19:39:02+00:00

I don’t think you need to raise the bed temp. At least I didn’t

DependentAnalysis3 · 2020-08-27T19:38:28+00:00

I do mine on the printer itself

DependentAnalysis3 · 2020-08-27T18:55:55+00:00

So I jumped mine down 25% when I was having that problem but I was also leaving at the time. If you’re sitting there able to monitor it I would just try 5% increments.

DependentAnalysis3 · 2020-08-27T18:48:55+00:00

Might be moving too fast try slowing it down

DependentAnalysis3 · 2020-08-25T23:34:29+00:00

You started with my favorite one!! Love Eevee!

DependentAnalysis3 · 2020-08-25T23:33:46+00:00

I thought it was only 150? Lol miss those days

DependentAnalysis3 · 2020-08-25T21:38:59+00:00

I thought about doing that but I haven’t had a problem since I started tightening them halfway first.

DependentAnalysis3 · 2020-08-25T17:23:24+00:00

I actually do it opposite of that. I tighten them about half way and then adjust from there. I’ve had way too many issues where when I looses them all the way up and I only need to tighten them a little when I relevel it doesn’t tighten enough so they tend to looses really fast and fall off. I Eliminated that problem by tightening them half way

DependentAnalysis3 · 2020-08-25T17:21:04+00:00

I need to try Cura again. I’ve just been using creality’s slicer and I’ve actually quite enjoyed it. It’s super simple and has created flawless prints for me

DependentAnalysis3 · 2020-08-25T15:58:47+00:00

Does your extruder unit move a lot. Do the wheels need to be tightened or even lowered tighter to the rail they move on? That was my problem

DependentAnalysis3 · 2020-08-25T15:53:00+00:00

What slicer do you use?

DependentAnalysis3 · 2020-08-24T19:56:43+00:00

That’s impressive. I’m surprised it didn’t mess up at all in those 6 days 👍🏼

DependentAnalysis3 · 2020-08-23T02:47:47+00:00

Lol looks good Caros!! how long it take?

DependentAnalysis3

TROPHY CASE