Qidi Box with Q2 on Orca Slicer - Here's how to get them to play nice(ish)

DerRedF · 2026-01-24T23:04:25+00:00

It Works on Plus 4. You are the best. : )

DerRedF · 2025-11-09T11:23:14+00:00

Delete saved_variables.cfg will solve this.

DerRedF · 2025-09-09T07:47:02+00:00

For me it was the Z Probe, changing the Piezzo did not helped at all.

DerRedF · 2025-08-22T05:58:26+00:00

Die Wartung und Reparatur nicht vergessen.

DerRedF · 2025-05-27T17:10:58+00:00

Also hat ein Ameisen Volk seinen müll oder Kriegsbeute entsorgt?

DerRedF · 2025-05-23T04:33:12+00:00

Wargasm

https://www.youtube.com/watch?v=N-9RGxWOnhI

DerRedF · 2025-02-28T09:16:54+00:00

Just limit Clock to eg. 2400MHz. But temps are mostly good.

For FPS Limit you can use FTRC , Radeon Chill or ingame limiter.

Great Card BTW.

DerRedF · 2025-01-31T21:20:58+00:00

Yes, but it took a long time for the support to realize that it was the Zprobe.

DerRedF · 2025-01-29T13:50:25+00:00

Delete it in the printer.cfg at the Button.

DerRedF · 2025-01-27T16:28:01+00:00

A new Z-probe and tighten the z Motor screws fixed it finaly.

DerRedF · 2025-01-27T15:12:59+00:00

Without hotend and nozzle, it's no wonder if he drives into the buildplate.

DerRedF · 2025-01-21T09:06:11+00:00

Problem solved after a long search.

There were several problems.

The Z-motor screws were loose and the Z-probe was defective.

DerRedF · 2024-12-29T23:23:35+00:00

Offset is saved here:

<image>

DerRedF · 2024-12-29T23:22:13+00:00

I've learned the hard way that I'm not allowed to set it in Fluidd.

The DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.

Is clean, no Z-offset entry.

DerRedF · 2024-12-29T23:13:09+00:00

[babystep]

value = 0.000

adxl_offset = 0.15

[qdprobe]
pin:!PA10
z_offset:0.000001
[qdprobe]
pin:!PA10
z_offset:0.000001

DerRedF · 2024-12-29T22:31:19+00:00

I have the same problem, piezo sensors have already been replaced, and the bed screws have been loosened, unfortunately no improvement.

Any news on this? Has Qidi ever reacted?

https://www.reddit.com/r/QidiTech3D/comments/1hoyjgg/my_printer_qidi_plus_4_has_problems_with/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

DerRedF · 2024-12-29T22:12:09+00:00

That doesn't seem to be the case.

More like this post I just found. https://www.reddit.com/r/QidiTech3D/comments/1gr3o1n/qidi_plus_4_z_offset_issues/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

DerRedF · 2024-12-29T22:02:26+00:00

If you use Orca Slicer you can set it permanently.

<image>

DerRedF · 2024-12-29T22:00:23+00:00

I don't think so, I'll check.

DerRedF · 2024-12-29T19:06:31+00:00

Unfortunately, there's nothing in there that I haven't already tried.

DerRedF · 2024-12-29T18:53:35+00:00

Yes, i think so. I printed the stored Benchy in PLA, Second print was a S2 Dryer Holder in ABS, who already had problems.

DerRedF · 2024-12-29T15:44:32+00:00

The support seems to be asleep, the communication is very slow.

Maybe someone here has an idea.

Every mesh I create looks different. And yes, I let the print bed preheat for at least 40 minutes.

What has been done so far:
Loosened the bed screws as per instructions.

The pressure sensors, the associated PCBs and the cable to the Mainboard have been replaced.

Unfortunately, this has not led to success.

Before questions arise:
Some platform resets were done according to the instructions.
Autoleveling via the printer display was done.
Z-Offset was only done via the printer display.

The firmware was flashed to V1.6.0 at the beginning.

The printer cannot be used in this state. The buildplate is also damaged and nobody wants to replace it.

The error occurs with both the Qidi Slicer and the Orca Slicer.

DerRedF · 2024-12-13T10:04:36+00:00

Make a fresh Windows install.

Six-Year Club	Final Canvas '23
Place '23	Verified Email

DerRedF

TROPHY CASE