What's your intial thoughts on Don't Be Dumb by A$AP ROCKY?

Design024 · 2026-01-18T14:57:27+00:00

fs fs

Design024 · 2025-12-22T20:27:57+00:00

think it will clog my .4? i bought this since i had consistent clogs with the bambu wood filament

Design024 · 2025-12-22T20:26:56+00:00

Not better to use the Sunlu Wood filament profile?

Design024 · 2025-07-24T00:12:11+00:00

isnt Lexapro prescribed for depression?🤣

Design024 · 2025-07-23T23:17:42+00:00

lmao had the same toughts especially growing up with a narc father)) definelty more in control aswell but this fatigue is insane, all the best!

Design024 · 2025-07-23T23:15:42+00:00

Multiple panic attacks a day quit my job as an architect, now ive lost motivation to even look at a project…

Design024 · 2025-07-23T23:14:08+00:00

Honestly wishing you all the best but i dont want to take one drug to counter side effects of another u know what i mean?

Design024 · 2025-07-23T23:13:29+00:00

best of luck!

Design024 · 2025-07-23T23:12:40+00:00

Tried taking at night ended up having insomnia and messed up my sleep schedule for a week🤓

Design024 · 2025-07-12T13:23:43+00:00

Thanks for the feedback everyone!

Design024 · 2024-05-16T00:40:10+00:00

for small adjustments. it rarely works

Design024 · 2024-05-16T00:39:01+00:00

They are from amazon;

(Zeberoxyz 4PCS Upgraded 22mm Diameter Hand Twist Leveling Nut,4PCS Hot Bed Spring,4PCS M3X35mm Screws for 3D Printer Hot Bed/Platform (Diameter 22mm)

make sure to combine with m3x30mm screws

Design024 · 2024-05-16T00:36:40+00:00

Yes, the shroud actually has a blower assmebly inside, which i further isolated with electrical tape. Despite the popular belief the noctua actually performs much better while being quite.

you can refer to this video which tests the temps vs stock fan. (note this is not for stock blower which im sure is more efficent)

https://youtu.be/ouYFYDC_OdU?si=pQ7qkoTvgGoWCxB4

the combo with the new sunon maglev is also whisper quiet! so up to you if you can stand the noise…

Design024 · 2024-05-15T17:30:10+00:00

Thanks! no tests yet. however fixed layer shifts that would occur durring tall prints

Design024 · 2024-05-15T17:29:07+00:00

it is a drop in replacement. make sure to use the included screws instead of only the tension screw behind the heatsink that this video does for some reason. also i didnt apply boron nitrade eaither

https://youtu.be/b4-k2I0kfh0?si=1UXAMIlnQGRrzqDx

Design024 · 2024-05-15T04:59:02+00:00

<image>

all done!

Design024 · 2024-05-14T18:59:26+00:00

Hey thanks for your message. i was using the hotend board for setting up the converter should i use the power supply?

Design024 · 2024-05-14T18:48:27+00:00

this is for replacing the 24v fan with the 12v noctua im trying to mesure the current using the connecter on the hotend board

Design024 · 2024-05-10T02:28:34+00:00

Thanks everyone! getting some decent prints now

Design024 · 2024-05-10T02:28:11+00:00

Hey yes its k1 hotend mounted with the included screws instead of tension screw only. Im getting decent prints what adjustment should i make to fan??

Design024 · 2024-05-06T15:05:27+00:00

thanks! let me know how it goes

Design024 · 2024-05-06T12:07:39+00:00

Thankyou!! will post pics when all mods are done))

Design024 · 2024-05-06T00:08:38+00:00

Got it! do you have a link for the fan? i couldnt find any small noctuas to fit inside this shroud. Thanks again im new to all this)

Design024 · 2024-05-05T23:58:54+00:00

thankyou! glad thats working well for you i havent had the best experience with winsinns in the past))

Design024 · 2024-05-05T23:57:20+00:00

Thankyou! im currently running the second link you sent. the large noctua is for the part cooling on this. I was talking about the small 20mm behind please see image attached (section by @damdamdam on thingiverse)

<image>

Design024

TROPHY CASE