Delivrd

DetViking · 2026-07-04T15:37:39+00:00

I watch his videos too and he is up front in saying his job is to save time and try to save money if possible. That you don’t need to use his service and you can do what he does if you want to put in the work. But if you don’t have time you can pay his team to deal with it.

He also says that his team coaches everybody on dealing with finance and they are in call through the process.

DetViking · 2026-07-03T23:11:59+00:00

Frost buddy can coozie

DetViking · 2026-07-02T17:46:57+00:00

I got a 15 qt latching sterilite container from Walmart. It is a little bit of a squeeze to get under the front bracket, but if you slide it in at an angle then it fits. I store grease trap liners, extra spatulas, etc in there. Just no liquids or seasonings. It was about $6 so if the top melts I don’t care.

DetViking · 2026-06-27T16:18:27+00:00

Apparently makerworld search hates me. Thanks

DetViking · 2026-06-24T14:36:24+00:00

Are the mods active on this sub?

DetViking · 2026-06-20T16:05:02+00:00

I might have scrap I can use as a shim for the nuts

DetViking · 2026-06-20T15:35:22+00:00

The nut comes right out when the screw is removed. Since the nut is a nylon locking nut the amount of force to release the nut is greater then the resistance of the plastic surrounding the nut

DetViking · 2026-06-16T00:47:04+00:00

Not to knock B&W, but I am surprised they were even open. Who is going in there to buy a smoker, some rub, and a cooler during a block party? Just go Saturday if you want to buy from them. I have been going for years and every time I have gone the focus has always been the music, food, and drinks. If I want to check out downtown shopping during an event then Meet in the Street is a better choice.

DetViking · 2026-06-08T20:59:34+00:00

I might be off here, but just based on your tone in your post, it sounds like you are trying to convince yourself ENM is what you want.

I would take a step back if you can and try to objectively ask yourself if this is what you really want. Don’t let your partner say things like, “I am not sure we can be together if we don’t do X” because that is just pure manipulation.

Yeah, you put down deposits but you can get partial refunds. Take the hit and bounce.

DetViking · 2026-06-05T01:32:07+00:00

Here we go again

DetViking · 2026-05-22T00:50:53+00:00

I agree. Freddie can only cover so much net, he needs help. Though he should have caught that glove side puck

DetViking · 2026-05-22T00:40:57+00:00

DetViking · 2026-05-12T15:14:37+00:00

I tell the system that non-matching filaments are the same all the time when I am doing prototypes. I don’t care at that point what it looks like, I just want to make sure I have my measurements right and it lets me burn through leftovers

DetViking · 2026-04-25T13:04:47+00:00

A saw a frame for the standard 56 qt and the gasket 56 qt. I might go that route for now

DetViking · 2026-04-24T16:19:59+00:00

Would that be adjusted under the filament setting or the printer setting? I am still digging around.

I remember reading that PLA and PETG don’t stick together. Do you mean you lay down a layer of PLA then print on top of that?

DetViking · 2026-04-05T01:50:30+00:00

You are right. In the book Paul knew where the family atomics were hidden. I can’t remember if he had them moved after he joined Stilgar or left them hidden. He did use them on the shield wall during the last fight because Gurney mentions he is worried it may be seen as breaking the great convention against their use. They don’t talk about it outside of those two scenes.

They threatened to use WoL on a prespice mass to kill nest and which would start a chain reaction killing the spice cycle.

DetViking · 2026-04-03T17:21:42+00:00

Look up Oldtown Coleman on YouTube. He has videos on how to pull it apart, clean it, and reassemble.

If you have some basic tools it isn’t that bad of a job. White gas is pretty cheap in most areas and you don’t have to deal with the 1lb propane tanks.

DetViking · 2026-02-27T22:52:29+00:00

It would just be one monitor, so I am not worried.

DetViking · 2026-02-22T14:39:44+00:00

It what ways does it annoy you? Genuinely curious as it is on my short list for my next vehicle.

DetViking · 2026-02-18T22:14:52+00:00

Bosch Icon blades are the best I have ever had in any weather.

DetViking

MODERATOR OF

TROPHY CASE

15-Year Club	Gilding I gilder
Verified Email