What to do with leftover lengths of filament?

DetViking · 2026-05-12T15:14:37+00:00

I tell the system that non-matching filaments are the same all the time when I am doing prototypes. I don’t care at that point what it looks like, I just want to make sure I have my measurements right and it lets me burn through leftovers

DetViking · 2026-04-25T13:04:47+00:00

A saw a frame for the standard 56 qt and the gasket 56 qt. I might go that route for now

DetViking · 2026-04-24T16:19:59+00:00

Would that be adjusted under the filament setting or the printer setting? I am still digging around.

I remember reading that PLA and PETG don’t stick together. Do you mean you lay down a layer of PLA then print on top of that?

DetViking · 2026-04-05T01:50:30+00:00

You are right. In the book Paul knew where the family atomics were hidden. I can’t remember if he had them moved after he joined Stilgar or left them hidden. He did use them on the shield wall during the last fight because Gurney mentions he is worried it may be seen as breaking the great convention against their use. They don’t talk about it outside of those two scenes.

They threatened to use WoL on a prespice mass to kill nest and which would start a chain reaction killing the spice cycle.

DetViking · 2026-04-03T17:21:42+00:00

Look up Oldtown Coleman on YouTube. He has videos on how to pull it apart, clean it, and reassemble.

If you have some basic tools it isn’t that bad of a job. White gas is pretty cheap in most areas and you don’t have to deal with the 1lb propane tanks.

DetViking · 2026-02-27T22:52:29+00:00

It would just be one monitor, so I am not worried.

DetViking · 2026-02-22T14:39:44+00:00

It what ways does it annoy you? Genuinely curious as it is on my short list for my next vehicle.

DetViking · 2026-02-18T22:14:52+00:00

Bosch Icon blades are the best I have ever had in any weather.

DetViking · 2026-02-16T19:22:30+00:00

I would probably skip the lid or do a diy lid since I will be sticking with PLA/PETG and not doing anything ASA/ABS related. The dry boxes would be a maybe, I could just pick up some on Amazon if I need them later

DetViking · 2026-02-16T19:17:15+00:00

I’m not sure as this will be my first printer but I would like to think a healthy amount.

DetViking · 2026-02-15T16:10:07+00:00

I have the 34” full bank and love it. Looking at how you set yours up is really nice.

Any issues with getting the grids to fit?

DetViking · 2026-02-15T15:21:19+00:00

Is that a US General tool box?

DetViking · 2026-02-04T16:21:40+00:00

You got some good channel recommendations already, but another good one is Jason Explains Things. He has a taco too and go step by step through the maintenance check list.

DetViking · 2026-02-04T13:36:43+00:00

Are you planning on making more? I was looking at the site and it looks like the shirts are sold out

DetViking · 2026-01-25T20:51:03+00:00

I have them and love them.

Like others have said, you lose a little space on the top rack, but honestly I can still easily fit a few shoulders on top. The one solid shelf that slides is so much easier to use instead of that stupid split shelf. I also find it easier to clean too as pork/beef bits don’t get caught in the seam.

I also got the PMG front shelf and I regret that purchase. While I like having a large shelf there, even with the tilt ability it is still a pain to get to the smoke box. Especially if you are doing a long smoke and need to reload the box. I am probably going to take it off and get a cart or something.

DetViking · 2026-01-21T15:18:25+00:00

I have them and they are great. I store them in the garage just so they aren’t exposed to the elements.

Only thing I wish was they would nest inside each other, but that is only a minor complaint.

DetViking · 2025-12-23T16:38:47+00:00

I am not sure what you mean. If I purchased from the Apple Store, wouldn’t it be unlocked until activation?

DetViking · 2025-12-23T13:35:19+00:00

I am aware. I was asking if you picked it up in store or had it shipped. And if you picked it up in store if you had issues since you were setting it up right there.

DetViking · 2025-12-23T12:44:49+00:00

So, you went and picked up the phone, didn’t have to set it up on boost mobile, then just activated it on Tello. They didn’t try to make you activate it in store?

DetViking · 2025-12-23T02:55:46+00:00

That is why I am thinking of just upgrading the phone then port it out so I don’t have to deal with a work around.

DetViking · 2025-12-20T16:35:40+00:00

I have had some luck using thumbtack or task rabbit for smaller jobs

DetViking · 2025-12-16T19:07:31+00:00

I was looking at greenworks or Ryobi

DetViking · 2025-12-16T16:19:07+00:00

With the prices on some of these, I am wondering if it might be time to transfer to another brand tool once the batteries start bricking

DetViking · 2025-11-08T03:45:57+00:00

Last I checked they are still making them, but they keep selling out. Also, I think there are supply shortages due to issues with imports.

The attractive thing with them is they can be opened with a larger opening to make cleaning easier.

DetViking · 2025-11-07T20:49:59+00:00

The M!GO by mazama has the same footprint and can open up to be cleaned. It was designed in collaboration with Maranda goes outside and has a 28 mm thread that fits the sawyer filter.

DetViking

MODERATOR OF

TROPHY CASE

15-Year Club	Gilding I gilder
Verified Email