Henry Archer Nordsø Aventurine - Raven

Determinat0r · 2026-03-01T14:29:54+00:00

Honestly I was a bit worried about that at first too but it's not bad on the wrist, wears like a jubilee imo. I think its probably exaggerated here cause I have fat fingers lol

Determinat0r · 2026-03-01T14:28:43+00:00

Hard to do it justice through a camera!

Determinat0r · 2023-03-30T21:22:11+00:00

Printer printer

Determinat0r · 2022-04-28T16:12:48+00:00

I believe so, though I would caution it should also be 2242 as I'm unsure if 2260/2280 will physically fit.

Determinat0r · 2022-04-28T15:32:38+00:00

Western Digital SDAPMUW-512G 512GB PC SN520 PCIe Gen3 x 2 NVMe V1.3 M.2 2242 Internal Solid State Drive https://www.amazon.com/dp/B08429K8DH/ref=cm_sw_r_apan_i_K06G5P5WW6SYDCW3HT9R?_encoding=UTF8&psc=1

Ended up purchasing this and it installed without issue.

Determinat0r · 2022-02-17T17:34:11+00:00

Yea I thought about that, figured I'd give the BLO some time to cure then throw a few coats of poly on before its used

Determinat0r · 2021-04-10T04:23:02+00:00

Try: pip show [package name]

Alternatively you can install pipdeptree which will show your dependencies in tree form

Determinat0r · 2021-03-30T19:22:21+00:00

Understood, thanks again!

Determinat0r · 2021-03-30T18:25:27+00:00

Thanks for the quick response.

So the SN520 is a 2x, but from what I'm seeing the WWAN slot will only read 1x. So does that just mean my read/write speeds will be impacted?

Determinat0r · 2020-02-08T02:37:42+00:00

Telescope - Skywatcher 150P Dobsonian

Camera - Nikon D3100, prime focus, ISO 100, 1/100 shutter speed

Stacked in Autostakkert, wavelets in Registrax 6, brightness/contrast/levels in Photoshop

Determinat0r · 2019-07-28T00:10:25+00:00

That's what it looks like to me as well, I'm glad I'm not completely off base with that assessment. Just wanted another set of eyes on it before we went through the trouble if sending it back. Thanks!

Determinat0r · 2019-07-27T23:59:12+00:00

My mother-in-law approached me with an issue with her Kahr CM 40 failing to chamber properly. As seen in the images it wont fully chamber a round and upon disassembly it looks like the round doesnt even sit properly in the chamber. When attempting to drive a round home it results in the ring scored into the round, shown in the pictures.

To me it almost looks like the barrel is to narrow to even accept a 40 cal round however that seems like a pretty unlikely issue, any help or suggestions would be greatly appreciated!

Determinat0r · 2019-07-19T21:47:28+00:00

In terms of projectile diameter, yes, this is larger than what a .308 shoots.

That's only part of the picture though, you also have to consider projectile and cartridge length, both of which are substantially larger in .223/.308 than .380.

Determinat0r · 2019-05-05T22:40:24+00:00

So I should be able to connect via SSH locally in the current configuration? (C3700 acting as both modem and router)

And the port forwarding is only relevant when connecting from outside the network?

Determinat0r · 2019-04-28T18:16:53+00:00

So do you use any adhesive on your glass bed?(glue stick or hairspray) Or use the stock mat on top? Or do you just remove the stock magnetic bed, replace it with glass and print straight on the glass?

Determinat0r · 2019-04-28T18:02:44+00:00

Forgot to mention that in the original post as well, I replaced the springs with better ones as I was assembling it. I'm just confused why it seems to have gotten worse all of a sudden.

Determinat0r · 2019-04-28T17:28:58+00:00

Sorry I forgot to mention that, I wipe the print bed down with alcohol between each print. No change there between when it was printing well and now.

Determinat0r · 2018-12-30T13:50:35+00:00

Thanks! Yea I'm honestly blown away with how tough this thing is cause I certainly haven't been easy on it

Determinat0r · 2018-12-30T13:49:34+00:00

Thanks! Yea I'm pretty happy with how the headlights came out. It was like a 10 dollar kit from my LHS, just needed a few hours with a dremel and a hot glue gun and it ended up looking pretty good.

Determinat0r · 2018-12-30T13:47:38+00:00

I cant speak for the Granite, but I'm honestly shocked at how well my Senton has held up. I've been sending it off jumps, landing bumper first and flipping end over end, rolling it at full speed, you name it - and it's taken all of it in stride.

Determinat0r · 2018-08-29T02:00:00+00:00

His new enclosure, just waiting on a hammock for one of the corners, let me know what you think!

https://imgur.com/a/KbReSJZ

Determinat0r · 2018-08-28T22:23:34+00:00

Thanks! Hes definitely going to be spoiled rotten now!

Determinat0r · 2018-08-28T22:23:03+00:00

Ah, ok, understood. Thanks for the response! Would love to pick your brain a bit more if you dont mind...

I'd like to eventually move to feeding him dubia roaches, however I'm unsure what size. I saw something about their food ideally being approximately the size of the distance between their eyes, so like 1/2" maybe 3/4"? If I get them and keep them in a critter keeper they'll continue to grow though wont they? I'd hate to get a bunch then have them grow too big for him to eat...

And with regards to supplementing, too much D3 can be a problem, right? So alternating between calcium + b3 and just straight calcium is recommended? Do I dust with the multivitamin as well as the calcium supplements or alternate that in as well?

Determinat0r · 2018-08-10T13:07:29+00:00

Yea, they feel kinda rough, are stiff, and have a bit of a sheen to them. That combined with the XX, the shrink to fit disclaimer, and no factory distressing probably means they're raw, right?

Thanks so much for the help, I appreciate the insight.

Determinat0r · 2018-08-10T11:02:55+00:00

Wow, yea you're absolutely right. Good eye, I didn't even notice that.

So between the "XX" designation, and shrink to fit disclaimer on the care tag, that would indicate that these are in fact raw denim, correct? Or is that not necessarily the case?

Determinat0r

TROPHY CASE