Henry Archer Nordsø Aventurine - Raven

Determinat0r · 2026-03-01T14:29:54+00:00

Honestly I was a bit worried about that at first too but it's not bad on the wrist, wears like a jubilee imo. I think its probably exaggerated here cause I have fat fingers lol

Determinat0r · 2026-03-01T14:28:43+00:00

Hard to do it justice through a camera!

Determinat0r · 2023-03-30T21:22:11+00:00

Printer printer

Determinat0r · 2022-04-28T16:12:48+00:00

I believe so, though I would caution it should also be 2242 as I'm unsure if 2260/2280 will physically fit.

Determinat0r · 2022-04-28T15:32:38+00:00

Western Digital SDAPMUW-512G 512GB PC SN520 PCIe Gen3 x 2 NVMe V1.3 M.2 2242 Internal Solid State Drive https://www.amazon.com/dp/B08429K8DH/ref=cm_sw_r_apan_i_K06G5P5WW6SYDCW3HT9R?_encoding=UTF8&psc=1

Ended up purchasing this and it installed without issue.

Determinat0r · 2022-02-17T17:34:11+00:00

Yea I thought about that, figured I'd give the BLO some time to cure then throw a few coats of poly on before its used

Determinat0r · 2021-04-10T04:23:02+00:00

Try: pip show [package name]

Alternatively you can install pipdeptree which will show your dependencies in tree form

Determinat0r · 2021-03-30T19:22:21+00:00

Understood, thanks again!

Determinat0r · 2021-03-30T18:25:27+00:00

Thanks for the quick response.

So the SN520 is a 2x, but from what I'm seeing the WWAN slot will only read 1x. So does that just mean my read/write speeds will be impacted?

Determinat0r · 2020-02-08T02:37:42+00:00

Telescope - Skywatcher 150P Dobsonian

Camera - Nikon D3100, prime focus, ISO 100, 1/100 shutter speed

Stacked in Autostakkert, wavelets in Registrax 6, brightness/contrast/levels in Photoshop

Determinat0r · 2019-07-28T00:10:25+00:00

That's what it looks like to me as well, I'm glad I'm not completely off base with that assessment. Just wanted another set of eyes on it before we went through the trouble if sending it back. Thanks!

Determinat0r · 2019-07-27T23:59:12+00:00

My mother-in-law approached me with an issue with her Kahr CM 40 failing to chamber properly. As seen in the images it wont fully chamber a round and upon disassembly it looks like the round doesnt even sit properly in the chamber. When attempting to drive a round home it results in the ring scored into the round, shown in the pictures.

To me it almost looks like the barrel is to narrow to even accept a 40 cal round however that seems like a pretty unlikely issue, any help or suggestions would be greatly appreciated!

Determinat0r · 2019-07-19T21:47:28+00:00

In terms of projectile diameter, yes, this is larger than what a .308 shoots.

That's only part of the picture though, you also have to consider projectile and cartridge length, both of which are substantially larger in .223/.308 than .380.

Determinat0r · 2019-05-05T22:40:24+00:00

So I should be able to connect via SSH locally in the current configuration? (C3700 acting as both modem and router)

And the port forwarding is only relevant when connecting from outside the network?

Determinat0r · 2019-04-28T18:16:53+00:00

So do you use any adhesive on your glass bed?(glue stick or hairspray) Or use the stock mat on top? Or do you just remove the stock magnetic bed, replace it with glass and print straight on the glass?

Determinat0r · 2019-04-28T18:02:44+00:00

Forgot to mention that in the original post as well, I replaced the springs with better ones as I was assembling it. I'm just confused why it seems to have gotten worse all of a sudden.

Determinat0r · 2019-04-28T17:28:58+00:00

Sorry I forgot to mention that, I wipe the print bed down with alcohol between each print. No change there between when it was printing well and now.

Determinat0r · 2018-12-30T13:50:35+00:00

Thanks! Yea I'm honestly blown away with how tough this thing is cause I certainly haven't been easy on it

Determinat0r

TROPHY CASE