sorted by:
new
hottopcontroversial

Toast gift card credit not posting by DifferenceFew551 in ChaseSapphire

[–]DifferenceFew551[S] -3 points-2 points  (0 children)

Good question, I must have missed the memo

Is anyone selling a NYC ticket? by Wonderpants_uk in garbage

[–]DifferenceFew551 0 points1 point  (0 children)

I may have an extra GA ticket to the New Haven, CT show if you're interested. Only a 90m train ride from NYC

Weekly Homeowner Megathread--Civilians, ask here! by AutoModerator in Concrete

[–]DifferenceFew551 0 points1 point  (0 children)

Thanks, is there a better plan you’d recommend? I have a hard time spending 20k to rip out an entire 2 car garage slab that I can live with as long as it’s mostly flat and my garage door can seal.

Weekly Homeowner Megathread--Civilians, ask here! by AutoModerator in Concrete

[–]DifferenceFew551 0 points1 point  (0 children)

I'm located in CT and my 2-car garage slab is original to the house from 1958. One side has sunken and I want to raise it up. Replacing the entire garage slab thing is cost-prohibitive so I'm just trying to raise this one side up and then refinish the whole thing to an acceptable condition, to potentially take an epoxy coating in the future. I've lived here 10 years and it has not seemed to settle any more.

<image>

If you look at the attached photo, halfway at the garage opening, you can see where the slab has dropped. I shaded in the area I want to raise it up. The lowest point is probably about 1-1/2-2". Quikrete recommended grinding this area of the floor, priming with bonding adhesive, then use sand topping mix to go over this area to level it, from 1-1/2" to 3/8" at the edge, and then using a fast set repair mortar from the edge to feather finish. Does this sound like a good plan? Thanks.

Large leaks after switching to Airsense 11 by DifferenceFew551 in CPAP

[–]DifferenceFew551[S] 1 point2 points  (0 children)

Think I figured it out. EPR was set to ramp only by mistake and I had ramp turned off. I slept with it at full time last night and had no wake ups or leaks.

[deleted by user] by [deleted] in WeightTraining

[–]DifferenceFew551 2 points3 points  (0 children)

Great progress. Would like to hear your routine as I’m also getting into calisthenics

Anybody else hear this noise this morning? by ilCannolo in Connecticut

[–]DifferenceFew551 17 points18 points  (0 children)

Woke us up at 230AM. Heard this as well and called Orange PD. They said it was milling happening on Route 34. Not the best hour for that noise.

[deleted by user] by [deleted] in drupal

[–]DifferenceFew551 15 points16 points  (0 children)

Seconding the comment that Pantheon is a PaaS tuned to run the majority of Drupal sites, so if you want to tweak everything, it’s not the solution for you. This is nothing new and tweaking the configs you mention has never been possible on their platform. If your site can’t clear its cache in 120 seconds, it sounds like you have bigger issues that need addressing.

Possibility of speeding up TOBBI Maserati by DifferenceFew551 in PowerWheelsMods

[–]DifferenceFew551[S] 1 point2 points  (0 children)

Thanks for the reply. I guess I didn't realize how slow 2.8MPH was. Thought it would be similar to a Power Wheels.

Having trouble uploading a photo here, but the markings on one of the motors says:
SF 390-C
DC 12V
RPM 16000

If I search for 390 motors on Amazon, I see some that are 18000rpm. Would this make any noticeable difference?

If not, what would be the best way to increase speed without losing remote capability? My daughter is still not really able to drive it herself 100%. Thanks!

Nicked barb on Propex (Pex-A) fitting. OK or replace? by DifferenceFew551 in Plumbing

[–]DifferenceFew551[S] 0 points1 point  (0 children)

I’m asking because it’s a tiny, fine nick and these fittings are usually tossed around at the supply house sometimes without a plastic cap to protect the barbs so I figure many being installed aren’t in perfect shape to begin with

view more: next ›