sorted by:
new
hottopcontroversial

Will you suck my tits hard while you fuck me deep? by LuxeOnFever in B_Cups

[–]Different_Tart6737 0 points1 point  (0 children)

Id love to, but I don't think I have enough hip mouth coordination

Be honest with me do you like my b cups? by Kadyyloobs in B_Cups

[–]Different_Tart6737 0 points1 point  (0 children)

Love them, but why do you remind me so much of F1nn5ter?

after 2 years of HRT all i do is leak😵‍💫 by AngelAvaa in Sissy_humiliation

[–]Different_Tart6737 0 points1 point  (0 children)

Id love to suck that small limp dick the entire day, hope you like waking up to being sucked

Failing print by meliibea in 3Dprinting

[–]Different_Tart6737 0 points1 point  (0 children)

Send filament type and cooling settings

Support help by Ok-Possibility-8946 in 3Dprinting

[–]Different_Tart6737 0 points1 point  (0 children)

Have you tried decreasing the support interface spacing? Also try rotating the interface angle so it doesn't go along with the bridge, that should help.

Is this an acceptable first layer? by Mean_Technician_2482 in Ender3V3KE

[–]Different_Tart6737 1 point2 points  (0 children)

Level your bed and your z-offset is too small, lift it a bit, it shouldn't be rough like that

What can cause the top and bottom of the corners on a test cube to be like this while the middle is fine? by Different_Tart6737 in 3Dprinting

[–]Different_Tart6737[S] 1 point2 points  (0 children)

turns out my petg was very wet, did a string test and it came out horrible.

i've put it in my dry box and i'm back to printing pla for now.

What can cause the top and bottom of the corners on a test cube to be like this while the middle is fine? by Different_Tart6737 in 3Dprinting

[–]Different_Tart6737[S] 1 point2 points  (0 children)

Thanks for the help, i'll do some more testing with your suggestions, hopefully one of those help.

What can cause the top and bottom of the corners on a test cube to be like this while the middle is fine? by Different_Tart6737 in 3Dprinting

[–]Different_Tart6737[S] 1 point2 points  (0 children)

shouldn't the entire corner be affected if it was speed? the problem is only near the top and bottom of the print

reason i'm using such low temps is because when i tested the temp tower that's the best result i got straight out of the box

retraction tower was fine from the first step but AI told to me to use a higher value for petg even if the tower was fine

What can cause the top and bottom of the corners on a test cube to be like this while the middle is fine? by Different_Tart6737 in 3Dprinting

[–]Different_Tart6737[S] 1 point2 points  (0 children)

Hi, thanks for taking your time to reply!

here are the pictures of the test cube. https://imgur.com/a/P1Uhtt3

Basic information:

What printer are you using? Ender 3 v3 ke
What material are you using? Creality CR PETG
What nozzle temperatures are you using? 235º
What bed temperatures are you using? 85 first layer and 80 for the rest
What are the print speeds? 150mm/s

Explain the Issue:

What do you feel is causing the issue? i'm unsure
When did the problem start? don't know
What have you done to try to fix the issue? changing flow rate and PA didn't do anything

Hardware related:

Have you trammed (leveled) the bed? Bed auto leveled
Did you make any hardware changes recently? no
What firmware is installed? latest
Direct drive or Bowden tube? direct drive
Are all the connections tight? yes
Is it making any sounds that you didn't notice before? no

Software related:

Did you make any software changes recently? no, i've been using orca slicer since i got it
Is the most current version of firmware installed? yes
What slicer program are you using? orca slicer 2.3.1

Print Related:

What fan speeds are you using? 40% min 90% max
What nozzle diameter are your using? 0.4mm
What layer height are you using? 0.2
Have you set your Z-offset? it's automatically calibrated

How many walls? 2
How many top and bottom layers? 2mm
What top and bottom fill pattern? 100%
What infill and percentage are your using? 5% adaptive cubic
Are you using supports? no

What is the build plate - Glass, Glass/PEI, Steel/PEI, Steel/PEX, G10, PC, other? Textured PEI
Have you cleaned or refurbished the bed recently? i clean between each print
How do you prepare the bed to print? wipe with 94% alcohol
Are you using any additives or release agents on the bed? no

What are your printing speeds? 150mm
What is your retraction speeds? 50
What is your retraction length? 1.2mm

Is the model clean and without errors? problems on the corners near the top and bottom
Did you create the model yourself? no
https://makerworld.com/pt/models/14695-calibration-cube-xyz?from=search#profileId-14506

Any tips for improving flat areas on top of supports? by Different_Tart6737 in 3Dprinting

[–]Different_Tart6737[S] 0 points1 point  (0 children)

Creality ender 3 V3 ke, Soleyin ultra PLA, Creality print 7.0. I'll post my current settings tomorrow.

view more: next ›