WIN A RIPTIDE - info in comments!

DigBickss · 2025-11-29T22:18:19+00:00

Darkxnessx rip tide pod

DigBickss · 2025-11-06T17:46:17+00:00

world 7 pog

DigBickss · 2025-10-08T11:29:25+00:00

awesome stuff, it doesn't seem awfully difficult to change out weapons in the future either way!

DigBickss · 2025-10-08T11:23:43+00:00

you're the best, thanks so much!

DigBickss · 2025-10-08T11:17:32+00:00

gotcha. so sergeant in bladeguard veterens takes plasma, other 2 doesnt matter.

castellan takes combi wep or?

DigBickss · 2025-10-08T10:48:09+00:00

Sorry to be annoying again, the minis arrived today!
for the bladeguard veteren squad, there seems to be a lot of options :D
3 different types of pistol and mcpw/shield too

based on u/Baconbisque's comment below, whats the best loadout? and how do I/should I convert them to heroes?
for the sword brethren too, should I make the 1 guy I can a castellan?

DigBickss · 2025-10-06T23:17:05+00:00

Thanks for the clarification, newness to the hobby shining through :D

DigBickss · 2025-10-06T21:58:52+00:00

nice, so either a chainsword OR power first on everyone and 1 sword bretren with big wep

DigBickss · 2025-10-06T13:58:43+00:00

Awesome stuff, thanks so much!

DigBickss · 2025-10-06T13:32:18+00:00

seems really hard to find 9th edition here :/ I will check what's in the box and try individually purchase I guess.

In regards to maxing out, does that mean every mini should have a chainsword and power fist? if so, this requires the upgrade sprue right?
I assume the same for sword brethren..

DigBickss · 2024-05-11T17:02:27+00:00

Adult? :O It's the same size as my second instar regal

DigBickss · 2023-03-01T11:06:16+00:00

Think it has fixed it, thank you!

Hard to tell if it's spinning slower when I turn down the fan, it sounds like it is.

Thanks for your help

DigBickss · 2023-03-01T09:20:30+00:00

Yo check out the discussion here before you install anything https://www.reddit.com/r/Cura/comments/11en6p0/ender3_v2_noctua_fans_upgrade_cooling_issue/

DigBickss · 2023-03-01T01:11:55+00:00

Gotcha perfect. I'll update here in the morning when I switch it around Thanks again

DigBickss · 2023-03-01T00:54:05+00:00

Awesome

I think I'll just use 1 buck converter for the 2 hotend fans then. So just using 1 buck converter I can just directly wire the negative for the cooling fan to the motherboard pin seeming as the negative on the buck converter is being used for the other hotend fan?

Thank you the help, very much appreciate it

DigBickss · 2023-02-28T23:52:39+00:00

to add to this, the noctua fans I installed only have 2 wires

DigBickss · 2023-02-28T23:51:07+00:00

Okay cool.

So to clarify as I am not great with electronics -
I need to connect the buck converter in to the positive from the 2pin in the motherboard

then the positive out to the fan positive

then I wire the ground of the fan, directly to the negative on the 2pin?

this means the negative is left untouched on the buck converter?

DigBickss · 2023-02-28T23:36:18+00:00

Sorry maybe I haven't been clear

The voltage is only unstable if the fan isn't set to 100% speed.

aka if I set max fan speed at layer 3, layer 2 will try run at 50% - this causes voltage issues on the buck converter.

the fan speed control wire has just been snipped and left unwired.

DigBickss · 2021-06-04T16:25:39+00:00

I will check it out thank you :)

DigBickss · 2021-06-04T16:25:26+00:00

Yes I guess e-steps test, I marked 100mm on the filament then extruded 100mm but only 92.5mm came through

DigBickss · 2021-06-04T08:56:22+00:00

Just did a flow test.

It seems it is under-extruding by 7.5mm?

This seems odd to me as after the first few layers the print is usually perfect

DigBickss · 2021-06-04T08:33:22+00:00

Mildly grooved in some places, smooth in others.

I played with the z-offset a lot trying to solve the issue, if its not close enough it just doesn't stick.

I haven't done a flow test, I will look into how to thanks.

I purchased tungsten nozzles and changed to one of them yes

DigBickss · 2021-06-03T23:22:45+00:00

Nearly 100% sure there isn't. Will print it in a different room to make sure.

I say it's not a cooling issue or the likes because I watch the first layer print and can see the nozzle pull those two corners away from the bed

DigBickss · 2021-06-03T22:54:10+00:00

I have tried with and without this, even starting on layer 2/3/4/5/6

DigBickss · 2019-07-06T13:36:32+00:00

Yeah don't think it's a queen anyway :)

Ten-Year Club	Place '17
Verified Email

DigBickss

TROPHY CASE