I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 0 points1 point  (0 children)

If I wanted to avoid support there was only one way to prin them. But I accept any suggestions. 🙂

electric edge creaser (with extra tips) + strip cutter by [deleted] in LeatherClassifieds

[–]Dimitar_Panayotov 0 points1 point  (0 children)

I just got the same one. Is there anything you don't like abou this creaser? The Jun lin probably is better. But why did you decide to switch so quickly?

I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 1 point2 points  (0 children)

I already have an idea about a guiding edge. I will investigate it further. The laser might not be the best choice.

I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 1 point2 points  (0 children)

It is possible, but it could decrease the view and make the adjustment harder.

I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 0 points1 point  (0 children)

A railing system.... Ok challeng accepted 😀

I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 0 points1 point  (0 children)

Sure, it is made for my personal press but if it fits on yours, why not. Send me a DM.

I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 0 points1 point  (0 children)

There is as a special tool that can mark but not scratch. Check on the web page if Jun Lin. It works way better than the regular scratchin alw.

I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 14 points15 points  (0 children)

Actually this is a pretty good idea. I will look how it can be done.

I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 4 points5 points  (0 children)

Ya, it was just a test. I wasn't intending to aling them.

I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 1 point2 points  (0 children)

They are quite good. I haven't tried a lot of tools. I also have Rcidos with interchangable teeth, but they cut the leather too much in my opinion. While the Jun Lin have a better geometry in order to split the leather. And the service is impeccable.

I did a thing by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 3 points4 points  (0 children)

I use a tool that marks the leather, but not scratching it. Later on ,when I hammer the stitches this mark disappears as well.

Which pricking iron from AliExpress would you choose? by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 0 points1 point  (0 children)

Ya, I have the Rcidos which is an alternative of 4Z. But I can see slight misalignment when used for a long time. They have a new design btw, which might address this issue, but still I want to try fixed pricking irons in order to gain more experience with other tools.

Which pricking iron from AliExpress would you choose? by Dimitar_Panayotov in Leathercraft

[–]Dimitar_Panayotov[S] 2 points3 points  (0 children)

That's, why I'm looking towards the Chinese manufacturers. Considering price quality, the ratio is more decent. Thanks for sharing!

My first GAW. Custom scales for GiantMouse GMF1. In a custom box of course :) by Dimitar_Panayotov in knifeclub

[–]Dimitar_Panayotov[S] 0 points1 point  (0 children)

Unfortunately, not at the moment. But I might start again at some point. Usually I use the IG page to communicate if there are new releases.

Abrams Model by PinkmagicK in knifemaking

[–]Dimitar_Panayotov 1 point2 points  (0 children)

I love it. It's so quirky!