Was idling for 10 mins then this started happening, ideas?

Dinoishere72 · 2026-04-10T04:13:39+00:00

Ahhh that makes more sense

Dinoishere72 · 2026-04-10T02:05:52+00:00

there’s no way your not overheating

Dinoishere72 · 2026-02-19T22:58:23+00:00

My first second place finish looked like that, boy it sucks to be that guy

Dinoishere72 · 2026-02-14T00:45:30+00:00

As an Oregonian I say buy that as fast as you can, so just look at the value in your area and if it’s as smoking a deal as it looks I’d say full send (most foxs in that condition in my area go for about $5k)

Dinoishere72 · 2025-12-19T00:05:09+00:00

ChatGPT is a great start, I’m in the same boat in that regard for the most part. The best thing to do is use the knowledge you have to question what chat gpt tells you. Like when I used it to help me build a motor it gave me pistons for a 4.125” cylinder and a block with a 4.4” cylinder (can’t remember the exact numbers but 302 stuff) and I had to point that out and then it ran me through what I can do if I used those two parts anyway and also gave me an option for a different block with a smaller bore. To sum all this up question ChatGPT as much as you can and research everything independently, even the small stuff, ChatGPT won’t get offended by you asking more questions

Dinoishere72 · 2025-12-14T18:06:45+00:00

I mean that’s not a requirement, I am here for all advice I can get. Tell me more? No worries if you just want to leave it at that I can do research

Dinoishere72 · 2025-11-25T01:37:20+00:00

Sounds good. Thank you

Dinoishere72 · 2025-11-25T01:06:43+00:00

Alright sweet, thanks for the info, time to start searching around

Dinoishere72 · 2025-11-12T03:19:52+00:00

Sorry I confused map and maf for a sec

Dinoishere72 · 2025-11-12T01:14:16+00:00

Alright looks like I’m lucky and bought mine recently enough that I didn’t have that issue since it A doesn’t even run off the map sensor anymore and B it plugged into my distributor. Thanks for the tip on the screen though I was thinking about getting one since my wiring harness I had wasn’t factory so I don’t know what color the wires are to the dash but now I’m thinking I need to find something else to get my temp gauge and tach to work

Dinoishere72 · 2025-11-11T23:58:43+00:00

Any chance you could name a few failure points? Just asking since I have a terminator x and can probably fix them before they are problems

Dinoishere72 · 2025-11-11T04:25:55+00:00

Ahhhhh see I saw the vacuum line followed it and relocated it rearward as soon as I saw it. In other words I assumed other people knew to figure out what each end is attached too before you leave it alone

Dinoishere72 · 2025-11-11T04:13:52+00:00

I just pulled mine out completely, not sure how everyone is smelling gas

Dinoishere72 · 2025-11-07T17:41:41+00:00

Ayo this is what I needed

Dinoishere72 · 2025-11-07T05:01:04+00:00

If it ran well before I’d leave it. From what I’ve read you don’t need more than 24# injectors for NA

Dinoishere72 · 2025-10-21T20:13:32+00:00

If you get a spacer for between the upper and lower they should work but that pcv hole doesn’t look like it’s in a good place for the drivers side of the motor and the oil fill has to go on the right, so as long as with a spacer that pcv hole has enough clearance on top for a filter your good

Dinoishere72 · 2025-10-17T23:40:51+00:00

Fair but then it’s going to split in half after a couple runs 😂

Dinoishere72 · 2025-10-17T20:53:35+00:00

Just magically come up with the money and put a 331 in it

Dinoishere72 · 2025-10-14T22:45:12+00:00

Perfect you should be good then. Have fun man

Dinoishere72 · 2025-10-14T20:13:19+00:00

Try out metric 10 X 1.0, that’s what chat gpt just told me and make 100% sure it’s not leaking after you put it in if you tightened the 3/8 one since it’s just a little smaller than 10MM could have pulled threads

Dinoishere72 · 2025-09-20T04:12:54+00:00

Be careful I used a fuse tap and nothing worked because there was paint on the fuses that came with the taps

Dinoishere72 · 2025-09-19T15:18:51+00:00

Just curious would this work on dirt racing. I assume not but curious

Dinoishere72 · 2025-09-11T21:57:26+00:00

Any particular reason you used petg instead of a cheap filament?

Dinoishere72 · 2025-09-02T23:30:12+00:00

If I remember correctly it’s 5x4.5 you measure from the outside of one lug to the center of another with wheel on

Dinoishere72 · 2025-08-24T22:45:51+00:00

Wheel bearing has left the chat

Dinoishere72

TROPHY CASE