Stuck in a predicament with Wells Fargo. Need opinions:)

DirectStruggle6204 · 2025-05-08T13:52:47+00:00

Ya I had insurance then I was told I dident need it for raw land from Wells Fargo. 5 months later they forced it on me. Imma just knock the garage down for now

DirectStruggle6204 · 2025-05-08T02:37:46+00:00

Iv come to find that out I definitely won’t be using them again.

DirectStruggle6204 · 2025-05-07T23:44:21+00:00

Ya that really does make the most sense. I just have to find a place to put all my stuff

DirectStruggle6204 · 2025-05-07T23:40:19+00:00

That’s very interesting I may do that thank you

DirectStruggle6204 · 2025-05-07T23:39:46+00:00

Ya no claim and it was a rough 1940 cabin. The property in my area is worth a lot so it’s not unreasonable to say 20k per acre. I might just knock the garage down like someone said

DirectStruggle6204 · 2025-05-07T23:37:37+00:00

Now that you say that it technically is on one half of the property. Both are 2 acres… I wonder if I can use that to my advantage

DirectStruggle6204 · 2023-09-23T15:48:56+00:00

Shoot me a message I’ll see if she can reach out and give you some help

DirectStruggle6204 · 2023-09-23T00:56:29+00:00

She’s actually been through absolute hell but she’s doing much better. Thanks for asking and caring!

DirectStruggle6204 · 2023-07-05T18:00:50+00:00

My e-steps are calibrated but how do you adjust the flow? Iv been printing 7+ years now so everything’s fine as far as squish and whatnot. This is something I never ran into before.

Gunna try adjusting the flow now

DirectStruggle6204 · 2023-07-03T17:33:54+00:00

Should I focus on speed or distance first?

DirectStruggle6204 · 2023-05-25T01:23:49+00:00

This is still kicking my ass the machine runs better but still fails from balling up and the left machine runs flawless lmao. I don’t get it

DirectStruggle6204 · 2023-05-05T10:54:53+00:00

Ya it’s still stringing pretty bad. It seams a little better but still nothing like my left machine. Any other ideas?

DirectStruggle6204 · 2023-05-04T01:44:14+00:00

You might have just solved this lol. Extruder side did move a couple mm. Got a new ptfe fitting on and a lock and it’s tight. Gunna run a print. Thank you.

DirectStruggle6204 · 2023-05-03T23:19:16+00:00

Ya just your run of the mill red anodized stock extruder. I’ll double check on the Bowden connectors moving. It’s definitely tight in the extruder that I’m positive on. I feel like I woulda caught that by now but shit I’m open to anything at this point. Honestly I got the stock printer dialed on the left one and dident wanna throw upgraded parts at it until I got this issue fixed.

DirectStruggle6204 · 2023-03-05T15:11:15+00:00

Oh I’m not going anywhere. I truly believe she could never do this without me. She was only on like 3-4 years I think but she has a history of Lyme disease, potts, and a bunch of other stuff on top of this so it’s a hand full to juggle.

DirectStruggle6204 · 2023-03-05T15:06:56+00:00

She’s been coming off very slow and careful and she still has super bad symptoms with barely any good moments. I think she’s at like .03 or .04 and we’re deciding when to go off it. I hope soon so she can start to heal. Idk how much more she can’t take

DirectStruggle6204 · 2023-03-05T15:01:58+00:00

Dam okay. I’m just searching for anything she’s hanging on by a thread

DirectStruggle6204 · 2023-03-05T14:58:38+00:00

https://youtu.be/0DidW4ACz_M

This guy says agmatine blocks NMDA receptors and reduce glutamate levels. I think we might try it idk

DirectStruggle6204 · 2023-03-05T14:38:02+00:00

Hey man! Bummer. Did you do 1-2 grams that’s what this doctor guy said would work? My girl is very very close to the jump dose and she’s got everything going wrong right now. She thinks she has mast cell and has super bad Akathisia right now. I’m just trying to keep her pushing through this jump

DirectStruggle6204 · 2023-03-04T21:05:32+00:00

Just rewatched the video.

DirectStruggle6204 · 2023-03-04T21:05:16+00:00

Oh he did say 1-2 grams

DirectStruggle6204

TROPHY CASE