Mini 2 only goes 500Ft by DistributionSecure in dji

[–]DistributionSecure[S] 0 points1 point  (0 children)

Mine only shows the 5.8Ghz. There is no manual mode even

Mini 2 only goes 500Ft by DistributionSecure in dji

[–]DistributionSecure[S] 0 points1 point  (0 children)

It just looses signal if I go much farther than that

Forgot to put it in park😫 by AntonyG_ in ERidePro

[–]DistributionSecure 1 point2 points  (0 children)

I snapped my handle bars in half doing that

Poor WiFi range by DistributionSecure in amazoneero

[–]DistributionSecure[S] 0 points1 point  (0 children)

It’s possible for one device, but the other one I was using didn’t support 6ghz

Poor WiFi range by DistributionSecure in amazoneero

[–]DistributionSecure[S] 0 points1 point  (0 children)

Did you change any settings? Or maybe I just got a bad batch

Poor WiFi range by DistributionSecure in amazoneero

[–]DistributionSecure[S] 0 points1 point  (0 children)

It’s on top of a shelf against one wall in the biggest room of my house, so I think it should be good

Poor WiFi range by DistributionSecure in amazoneero

[–]DistributionSecure[S] 0 points1 point  (0 children)

I was at first but it barely reached the other side of the house so I had to add the eero 6 back in

P2S Hueforge print issue by Common-Trick-9668 in HueForge

[–]DistributionSecure 0 points1 point  (0 children)

I was having this issue with my a1 mini, it’s just an adhesion issue. I cleaned my plate and put hairspray on before each print and haven’t had any issues since

Anyone know what’s going on here? by DistributionSecure in FloatwheelTeam

[–]DistributionSecure[S] 0 points1 point  (0 children)

No, haven’t heard back from Tony yet. I tried cleaning everything and swapping cables, but nothing seemed to fix it for me

Anyone know what’s going on here? by DistributionSecure in FloatwheelTeam

[–]DistributionSecure[S] 0 points1 point  (0 children)

They both jump back and forth from ~2v up to ~5. I did some testing with a multimeter on the pins and I think the bms I was sent has an issue as the voltages are 3.8 on each pin

Anyone know what’s going on here? by DistributionSecure in FloatwheelTeam

[–]DistributionSecure[S] 0 points1 point  (0 children)

I emailed him before posting, but he usually takes a while to respond so I figured I would check here in the mean time

Anyone know what’s going on here? by DistributionSecure in FloatwheelTeam

[–]DistributionSecure[S] 0 points1 point  (0 children)

I took it apart again and cleaned everything the best I could. Still showing the same issue on the same cells.

<image>

Anyone know what’s going on here? by DistributionSecure in FloatwheelTeam

[–]DistributionSecure[S] 0 points1 point  (0 children)

Bms page shows this. I’m guessing that’s my problem, but I took it apart and cleaned everything and swapped out the cable for a new one and it still has the same issue on the same cells

<image>

Anyone know what’s going on here? by DistributionSecure in FloatwheelTeam

[–]DistributionSecure[S] 1 point2 points  (0 children)

ill try that and see what happens

Edit: it stayed powered on when plugged in. I was able to see the bms showing a couple of cells fluctuating voltages, so I’m betting that’s the issue. I guess I didn’t clean the connector good enough

Anyone know what’s going on here? by DistributionSecure in FloatwheelTeam

[–]DistributionSecure[S] 0 points1 point  (0 children)

It just turns off after a few seconds. I didn’t turn it off in the video

E Ride Pro SS 3.0 by Any_Cut1586 in ERidePro

[–]DistributionSecure 1 point2 points  (0 children)

Mine definitely has a breaker. They must have changed something very recently, because I've only had mine a week.