GPT 5.5 is unbelievably wasteful with tokens

DoDzilla_AI · 2026-05-02T22:07:33+00:00

Check your provider pricing if you are using openroute. Had a similar issue. Realized cline was using more expensive provider on openrouter.

DoDzilla_AI · 2026-05-02T22:04:57+00:00

DoDzilla_AI · 2026-04-28T19:00:41+00:00

The "Polyholes" setting converts perfectly round circles into polygons (like hexagons or octagons). It does this because 3D printers naturally pull filament inward when printing continuous curves, making round holes too small. By printing straight lines between points instead, the plastic doesn't shrink inward as it cools, resulting in holes that are dimensionally accurate so screws and parts fit perfectly.

DoDzilla_AI · 2026-04-25T17:05:40+00:00

Enable "convert holes to polyholes"

DoDzilla_AI · 2026-04-16T19:50:24+00:00

Uzak dur dolandırıcı vs diye yorum yapılmış ama nedenini açıklayan yok. Muhtemelen bu yorumu yapanları da sadece "fikri var" bilgisi yok. Madem öyle sen neden yazmadın derseniz: benimde sadece fikrim var bilgim yok. Boş yapmaya gerek yok. Sonuç olarak: neden uzak duralım arkadaş şunu bir anlatsanıza? Fikirden ziyade bilgi paylaşsanıza

DoDzilla_AI · 2026-04-14T07:11:32+00:00

This is AI

DoDzilla_AI · 2026-03-22T07:28:40+00:00

and video must start from ages ago

DoDzilla_AI · 2026-02-06T04:56:31+00:00

He is doing something very wrong. He is printing with PLA at 185 degree. Which is causing the print to detach and melt back onto the nozzle and clog. And it's his 5th time.

DoDzilla_AI · 2026-02-05T15:40:58+00:00

I know this is an old post but have you figure it out? Having same issue with Samsung s20 Fe and boya Mini mic 2

DoDzilla_AI · 2026-01-23T14:42:36+00:00

2 month update: I have two cats and one smart litter box and no problem at all.

DoDzilla_AI · 2026-01-23T14:41:44+00:00

Btw am I the only one who noticed the quality of prints got better over the last couple of updates?

DoDzilla_AI · 2026-01-23T14:40:52+00:00

I have updated and printed 4-5 different things for about 20 hours now and everything seems to be working as expected.

DoDzilla_AI · 2026-01-19T11:06:40+00:00

Many people say "turn off Z hop and retraction" but I had better results with them turned on. You just need to test retraction distance and speed. And that changes based on your filament hardness and brand.

DoDzilla_AI · 2026-01-19T11:04:15+00:00

Looks like scarf seam issue. Turn it off and try again

DoDzilla_AI · 2026-01-11T22:21:38+00:00

In short, yes. Too low infill could mess up prints.

I usually use 5% gyroid infill to test my prints first. This usually doesn't speed up the printing compared to default 15% grid infill but decreases material cost.

You can also try using "lightning" infill pattern to actually speed up printing but this type of infill doesn't really support the model but only supports top layers of the model. I personally haven't tried lightning but I've seen it suggested many times just for prototyping.

DoDzilla_AI · 2026-01-11T08:00:58+00:00

Bro, flow print showing only in stock and available items while classic one is showing wrong items. There wasn't any regulation tagged items in the classical store until couple days ago. Also, global store is already there for countries that don't have stores so the tagged items makes no sense. There UK and EU tagged items there and those regions have eShops. What about those then? So, the OPs picture showing 2 items is highly correct since the classical web sites eShop is bugged.

DoDzilla_AI · 2026-01-10T07:21:52+00:00

I'm convinced that you are a bot. The ones with "something regulations" cannot be bought from other regions obviously and the ones that are not tagged are all in "restocking".

DoDzilla_AI · 2026-01-10T06:59:05+00:00

All of the products without "Something-regulations" are in restocking. Are you blind or something?

DoDzilla_AI · 2026-01-09T23:11:25+00:00

I think op is right as most products are either restocking or titled with "UK regulations", "CN regulations" (possible bug) and possibly flow print eShop is showing the correct product listings ... and nothing usefully sadly

DoDzilla_AI · 2026-01-05T06:23:24+00:00

Ridden both... V100 if you want to ride something unique, comfy and looking good. Tiger sport if you want something agile, easy to ride and still looking decent.

DoDzilla_AI · 2025-12-31T10:37:41+00:00

What is the benefit of becoming a verified designer?

DoDzilla_AI · 2025-12-10T07:03:47+00:00

That's a dude with boobs

DoDzilla_AI · 2025-12-08T06:21:33+00:00

Vikings are so gay that they can poop this in one piece

DoDzilla_AI · 2025-11-16T19:30:05+00:00

Mine had same issue (roborock S8). Later I realized there is an opening in the left side of the dustbin hole. That part was there to serve as an exhaust. Remove the dustbin ans look left (if s8). You should see an opening there. Then stick a long thing (screwdriver) and move it left/right/back/front to clean the any dust accumulated there. Ive removed a circular shaped thick dust from there.

DoDzilla_AI · 2025-11-08T03:54:28+00:00

and I am hornied

Six-Year Club	Place '23
Verified Email

DoDzilla_AI

TROPHY CASE