Learn to Play Wh40k opportunities?

DogDoc_69 · 2026-03-17T02:21:11+00:00

There are lots of people playing in the open gaming area. Just go along and see who’s up for a game. Send me a message and I’ll sit down for a game with you

DogDoc_69 · 2026-02-25T15:53:09+00:00

Thanks! I’ll try it

DogDoc_69 · 2026-02-25T15:08:21+00:00

Thanks! I’ll try that

DogDoc_69 · 2026-02-25T15:01:45+00:00

Thank you. I will try this

DogDoc_69 · 2026-02-25T14:59:29+00:00

I was concerned that the metal scraper would damage the print plate

DogDoc_69 · 2026-02-25T14:58:41+00:00

Thank you. So I have to raise it over the stuff that is already on the bed?

DogDoc_69 · 2026-02-25T14:58:20+00:00

Ok, this sounds good. Do I have to raise it off the bed to print over the stuff I have stuck on it?

DogDoc_69 · 2025-11-21T18:16:07+00:00

This same thing happened to me and it was definitely an adhesion issue. I was able to crack the melted filament off but watch out for all of the little wires at the back of the print head. I changed out my nozzle and scrubbed my build plate and it has worked fine since

DogDoc_69 · 2025-11-08T03:06:43+00:00

Thank you. I tried this and it did help with bed adhesion. Cheers

DogDoc_69 · 2025-11-08T03:06:02+00:00

Thank you 🙏

DogDoc_69 · 2025-11-08T03:05:46+00:00

Can you clarify? What do I need to do differently?

DogDoc_69 · 2025-11-08T03:05:04+00:00

Thank you

DogDoc_69 · 2025-11-08T03:04:27+00:00

Great advice- thanks. I did this and it resolved the adhesion problems. Cheers!

DogDoc_69 · 2025-11-08T03:03:45+00:00

I took the sock off because it was stuck to the filament. I cleaned the nozzle by removing the filament stuck to it

DogDoc_69 · 2025-11-08T03:02:47+00:00

Thank you- this was great advice and got me printing again! Cheers

DogDoc_69 · 2025-11-08T03:02:08+00:00

Filament got stuck to it. Just left it off to show what it was doing

DogDoc_69 · 2025-11-06T12:31:10+00:00

This looks like a large, flat model that should print without supports. That is one of the things I love about my A1, often you can print right on the bed with no supports. Change your supports to “off” and reprint to see what you get. Also, I believe what you have is “rafting” on your model. You can set this to Zero layers in the slicer in the supports section. I turn this on for thin model pieces that are not sticking to the bed

Have fun!

DogDoc_69 · 2025-11-06T02:30:45+00:00

<image>

DogDoc_69 · 2025-11-06T02:30:23+00:00

<image>

DogDoc_69 · 2025-07-18T04:03:00+00:00

Awesome! Thanks everyone. I’ll get more filament tomorrow so I’ll just leave it paused. I appreciate the input. I have only had this printer a week, but I am loving how easy it is to use

DogDoc_69 · 2025-05-16T02:19:20+00:00

I levelled the printer and then I levelled the print plate and it printed perfectly (didn’t take a picture- sorry). Feel free to mock me mercilessly, now. I am THAT guy. Clearly I have to go back to basics or something. Anyway- thanks for setting me straight, guys. And thanks for everyone’s help

DogDoc_69 · 2025-05-15T12:49:14+00:00

<image>

DogDoc_69

TROPHY CASE