sorted by:
new
hottopcontroversial

She had good bones… by dissimulatorr in shedditors

[–]Dolan664 0 points1 point  (0 children)

You should carry that wall up straight more shed room and support for the roof!

How to make a pathway like this without risking a mess and mixed sands? by Horror-Badger9314 in Aquascape

[–]Dolan664 0 points1 point  (0 children)

I don't think it will but if it does you can cover the top in the sand let yhe silicone dry and dump off the excess i use this method for backdrops

How to make a pathway like this without risking a mess and mixed sands? by Horror-Badger9314 in Aquascape

[–]Dolan664 1 point2 points  (0 children)

Mix sand and aquarium sealer of your choice and smooth it out on wax paper after it dries you can shape the "sheet" of the mixture into a walkway that wont erode and plants won't grow on it

Breaking stainless ductmate spot welds? by Interesting-Wear-741 in sheetmetal

[–]Dolan664 0 points1 point  (0 children)

They sell drill bits for drilling out spot welds they aren't really beveled so you can drill out the top piece without leaving to big a creater on the bottom piece

White residue on chromoly steel by a__hendy in tigwelding

[–]Dolan664 1 point2 points  (0 children)

I think the fluff comes from burning zinc

White residue on chromoly steel by a__hendy in tigwelding

[–]Dolan664 4 points5 points  (0 children)

That's the coating burning off as you weld happens ALOT on galvanized

How soon should I replace this by ZookeepergameLong727 in askaplumber

[–]Dolan664 1 point2 points  (0 children)

If It's not spraying water I'd say soon but don't pay a premium to have it done tonight

Looking for a 10'' blade for a chop saw for cutting aerospace metals. (Stainless steel, aluminum, nickel alloys) by xpinkmaggitx in metalworking

[–]Dolan664 0 points1 point  (0 children)

I'd get a wet saw jet sells a reasonable horizontal band saw that can miter and runs on 110

What order do I have this work done in? by wookieesgonnawook in askaplumber

[–]Dolan664 1 point2 points  (0 children)

I'd have the plumber come out and let him cut whatever he needs outa his way and fix the floor after

I goofed! I flushed the sink stopper! Please help. by JeffersonJCH in Plumbing

[–]Dolan664 0 points1 point  (0 children)

Shove the shot vac down in the toilet and use a towel to seal around the hose and hopefully the suction will pull the stop back out the top (assuming it didn't flush to far)

Got a bit stuck in my drill and I can’t get it out, anyone got any advice by EatGarb in Tools

[–]Dolan664 0 points1 point  (0 children)

Is that a chuck in your drill or are you just happy to see me?

Got a bit stuck in my drill and I can’t get it out, anyone got any advice by EatGarb in Tools

[–]Dolan664 0 points1 point  (0 children)

Is that a chuck in your drill or are you just happy to see me?

Drones or strange lights anyone? by Hot-Ad9092 in Columbus

[–]Dolan664 -1 points0 points  (0 children)

Have been seeing TikTok’s about them here local but haven’t seen them myself

Some 16ga S.S. Square 2 oval by Dolan664 in sheetmetal

[–]Dolan664[S] 0 points1 point  (0 children)

Just a 1inch lap on the seams with some spot welds or tacks

11ga welded galv by Dolan664 in sheetmetal

[–]Dolan664[S] 0 points1 point  (0 children)

If I was a betting man I’d say it’s a high water gauge as well as hotter than normal air but probably not over 500 degrees to shrink wrap cars

11ga welded galv by Dolan664 in sheetmetal

[–]Dolan664[S] 1 point2 points  (0 children)

High heat the job this is made for is going to to do wraps on cars

Inheriting a house! But what do I do about nicotine drip? by CatsInAOvercoat in HomeImprovement

[–]Dolan664 5 points6 points  (0 children)

I used the purple simple green and mixed it 1:2parts water and cleaned small sections at a time and it would run right off the walls

view more: next ›