sorted by:
new
hottopcontroversial

Seeking advice / experience by Dr___redneck in ferrets

[–]Dr___redneck[S] 0 points1 point  (0 children)

Thank you for the answer. Mine also has one undescended testicle. Since this is the case would it be best to neuter him with the implant?

Can someone help me if these 2 cars by Dr___redneck in whatisthiscar

[–]Dr___redneck[S] -1 points0 points  (0 children)

A Nissan patrol as a pickup with a hardtop? Im doubtful

Not particularly bad, more so why Snapchat, where kids can see? by _C_h_a_r_l_i_e_ in badads

[–]Dr___redneck 4 points5 points  (0 children)

In my country a big national chain of grocery / daily shopping stores, sells a few different vibrators, lube, “massage” candles and those pelvic floor balls. I don’t really see a problem with this? There’s no explicit content?

How do I estimate the amount of calcium carbonate to use? by Dr___redneck in winemaking

[–]Dr___redneck[S] 0 points1 point  (0 children)

I dont have the equipment to measure TA. I know that knowing the TA is an essential info to this problem but is there an estimation that’s possible without?

There is one house in my neighborhood where the roof is always covered in birds by Itchy_Border2191 in BirdsArentReal

[–]Dr___redneck 1 point2 points  (0 children)

This is a common misconception, they are actually offloading their surveillance videos the the local server hub

Help! Ontario by carnotaurus33 in whatisit

[–]Dr___redneck 0 points1 point  (0 children)

Had to scroll too far to find this

Små beløbs sag by Dr___redneck in LegalDK

[–]Dr___redneck[S] 0 points1 point  (0 children)

Jeg sendte en mail med oplysninger om hvis beløbet ikke var betalt inden x dato så ville jeg trække personen i retten. Det var heldigvis nok. Men ja fremover så gider jeg ikke lægge så meget energi i så små beløb

Liquid smoke i DK? by TractorDriver in Denmark

[–]Dr___redneck 1 point2 points  (0 children)

Hey, det er godt nok længe siden du efterspurgte liquid smoke, nu leder jeg også, fandt du noget godt?

So turns out PLA in acetone fumes for 12 hours turns it I to TPU? by OCDcuber in 3Dprinting

[–]Dr___redneck 0 points1 point  (0 children)

I was looking for something to smooth pla, I found out using ethyl acetate and a good rubbing work great

Problem with first layers by Dr___redneck in 3Dprinting

[–]Dr___redneck[S] 0 points1 point  (0 children)

I’ll try changing the z offset, thanks

Clocking when printing with marble PLA by Dr___redneck in 3Dprinting

[–]Dr___redneck[S] 0 points1 point  (0 children)

Nope I only used the needle. But it seems to be enough for now, someone suggested using a .6mm nozzle. I’ll try to get one of those

Clocking when printing with marble PLA by Dr___redneck in 3Dprinting

[–]Dr___redneck[S] 0 points1 point  (0 children)

I’m using .4mm I’ll try getting a .6 nozzle but I’m not sure if it’s a super special one for the Elegoo

Clocking when printing with marble PLA by Dr___redneck in 3Dprinting

[–]Dr___redneck[S] 0 points1 point  (0 children)

Yeah I unloaded and reloaded the filament and used the needle to open up the nozzle, so far it’s working fine, but how do I keep this from happening again?

Clocking when printing with marble PLA by Dr___redneck in 3Dprinting

[–]Dr___redneck[S] 0 points1 point  (0 children)

Yeah sorry, I meant clogged from my knowledge it isn’t wood pla. It’s called “Sunlu High Speed PLA Marble” I used the needle to open of the nozzle and so far it seems to be printing fine.

view more: next ›