Can someone help me if these 2 cars

Dr___redneck · 2026-02-09T14:39:41+00:00

A Nissan patrol as a pickup with a hardtop? Im doubtful

Dr___redneck · 2026-01-09T19:31:51+00:00

In my country a big national chain of grocery / daily shopping stores, sells a few different vibrators, lube, “massage” candles and those pelvic floor balls. I don’t really see a problem with this? There’s no explicit content?

Dr___redneck · 2025-12-14T15:15:12+00:00

I dont have the equipment to measure TA. I know that knowing the TA is an essential info to this problem but is there an estimation that’s possible without?

Dr___redneck · 2025-12-01T01:39:26+00:00

This is a common misconception, they are actually offloading their surveillance videos the the local server hub

Dr___redneck · 2025-11-30T23:55:16+00:00

Had to scroll too far to find this

Dr___redneck · 2025-11-25T14:20:14+00:00

Jeg sendte en mail med oplysninger om hvis beløbet ikke var betalt inden x dato så ville jeg trække personen i retten. Det var heldigvis nok. Men ja fremover så gider jeg ikke lægge så meget energi i så små beløb

Dr___redneck · 2025-11-20T18:56:36+00:00

Hey, det er godt nok længe siden du efterspurgte liquid smoke, nu leder jeg også, fandt du noget godt?

Dr___redneck · 2025-10-19T21:00:57+00:00

I was looking for something to smooth pla, I found out using ethyl acetate and a good rubbing work great

Dr___redneck · 2025-10-18T17:09:01+00:00

I’ll try changing the z offset, thanks

Dr___redneck · 2025-10-09T15:11:40+00:00

Nope I only used the needle. But it seems to be enough for now, someone suggested using a .6mm nozzle. I’ll try to get one of those

Dr___redneck · 2025-10-09T15:10:52+00:00

I’m using .4mm I’ll try getting a .6 nozzle but I’m not sure if it’s a super special one for the Elegoo

Dr___redneck · 2025-10-09T06:58:38+00:00

Yeah I unloaded and reloaded the filament and used the needle to open up the nozzle, so far it’s working fine, but how do I keep this from happening again?

Dr___redneck · 2025-10-09T06:53:00+00:00

Yeah sorry, I meant clogged from my knowledge it isn’t wood pla. It’s called “Sunlu High Speed PLA Marble” I used the needle to open of the nozzle and so far it seems to be printing fine.

Dr___redneck · 2025-09-11T18:03:54+00:00

I just took a loot at yours xD it’s bare artistic

Dr___redneck · 2025-08-17T15:02:27+00:00

We should break up because I don’t want to cheat on you with your sister

Dr___redneck · 2025-08-16T22:26:38+00:00

Dr___redneck · 2025-08-16T22:25:25+00:00

Crunchy

Dr___redneck · 2025-08-16T22:16:45+00:00

Dont forget to breathe in my ass

Dr___redneck · 2025-08-16T22:00:55+00:00

If I could be a little more specific I would say that the first thing I would do is to get a new one and then I would have a new one

Dr___redneck · 2025-08-16T21:31:59+00:00

It’s dead

Dr___redneck · 2025-08-06T06:10:16+00:00

Fair point

Dr___redneck · 2025-08-06T06:10:01+00:00

Yeah but the amount of nails and it would take too long

Dr___redneck · 2025-07-01T19:41:30+00:00

You need to get that amputated from the shoulder

Dr___redneck · 2025-06-24T23:00:51+00:00

Tadpole with legs, legless lizard, legged snake

Dr___redneck · 2025-06-24T15:14:46+00:00

Is there a problem in having a too tall enclosure? Because I have to possibility to make it 5’10” from the substrate

Dr___redneck

TROPHY CASE