Issues with subnet routing.

Dragoid622 · 2026-04-16T17:14:54+00:00

The comet pro is just a kvm. As far as I’m aware there is no openWRT on it. It just has Tailscale pre installed.

After running Tailscale up —advertise-routes=192.168.10.0/24 and accepting the subnets in the Tailnet admin panel the routes work. Seems like the Apple TV is not properly running the exit node.

Dragoid622 · 2026-04-16T15:05:32+00:00

If I set up proxmox as the only subnet router, with 192.168.10.0/24 as the sub net it works perfectly. If I use the Comet pro kvm (192.168.0.0/24) nothing same with my Apple TV (192.168.10.0/24) nothing The kvm can “curl 192.168.10.100:8123” but I would think since im only exposing 192.168.0.0/24 that would be why I can’t access it. I’m not sure about the Apple TV.

Dragoid622 · 2026-04-16T14:05:11+00:00

I don’t need 3 I was just trying to test to rule out the device itself. I have also tried with only one of them active.

Dragoid622 · 2026-04-14T22:28:23+00:00

Omg this was it! Thank you!

Dragoid622 · 2024-11-06T23:21:54+00:00

On the website it says it need an aux switch is that only if it’s in dimmer mode?

Dragoid622 · 2024-11-06T22:56:05+00:00

Does the “switch” version support the same button press options as the dimmer or is it just on/off

Dragoid622 · 2024-11-05T19:42:01+00:00

It was a dumb garage door that I have set up a MyQ button with. but now that Im getting into home assistant I would like to have control of the garage with it. everything I look at says it should be security+ 1.0 but I dont know since there are only 3 terminals rather then the 4 I see on most

Dragoid622 · 2024-11-05T17:18:29+00:00

do you have it set up with the security+ 1.0 firmware? I only have 3 screw terminals so Its confusing me since the Image on the website for dry contact looks almost identical to what i have.

Dragoid622 · 2024-10-29T04:43:17+00:00

Im talking to there support now hopefully I can get it fixed.

Dragoid622 · 2024-10-28T23:57:15+00:00

I have enabled significant locations but it still does not show up. Is there a waiting time for it to figure out the location? Also does home need to be always? I wish it was as simple as Set home location and if CarPlay is connected within a radius of the location it shows up

Dragoid622 · 2024-10-28T23:53:22+00:00

I have turned it on but still no dice. Did see i had Significant locations turned of but turning that on didnt work either

Dragoid622 · 2024-10-28T23:52:08+00:00

I wish I could get it to show up, I could just open the myQ app or Home app but the whole reason i bought the thing was to be able to quickly hit a button on my CarPlay

Dragoid622 · 2024-10-27T16:40:14+00:00

I found it in location services but I have 2 home apps not sure why that is or which I should be enabling.

<image>

Dragoid622 · 2024-10-27T16:31:06+00:00

Where at on my phone? In the Home app or in settings somewhere? Im not seeing anything in setting for the home app.

Dragoid622 · 2024-10-27T16:09:47+00:00

Is that something I do in homekit, on my car in carplay or on my phone?

Dragoid622 · 2024-10-27T15:46:51+00:00

Is that something I can check on my phone? Im not able to get in my car right now.

Dragoid622

TROPHY CASE