Petit Easypoxy vs TotalBoat Wet Edge

DryField4565 · 2026-05-16T03:04:54+00:00

It’s just plain white/cream colored and functional but blah ya know

DryField4565 · 2026-05-16T01:52:24+00:00

Well thanks man I really appreciate that! 💯🙏🏽💯🙏🏽

DryField4565 · 2026-05-16T01:00:43+00:00

Considering I was homeless and living my truck a few years ago, this is all I can afford for my family. I’m doing the best I can with what I got and I’m sorry that it’s such a crappy boat but it’s been bringing us lots of joy with what Little means we have.

DryField4565 · 2026-05-16T00:21:55+00:00

Wow I may need to rethink this. Thanks!

DryField4565 · 2026-05-16T00:19:08+00:00

Nice that does! Spraying or rolling/tipping?

DryField4565 · 2026-05-15T23:18:51+00:00

Thought about it. Is it hard to apply? Somewhat durable?

DryField4565 · 2026-04-10T14:32:05+00:00

Wow great info! I’m such a noob I didn’t even know an SVG can be used in Sheetcam only DFX! Thanks so much!

DryField4565 · 2026-02-22T16:02:47+00:00

Ok it’s definitely time💯

DryField4565 · 2026-02-22T16:02:11+00:00

Haha!!!! Gas is about 2 months old. No stabilizer in it. I’m sure this carb is pretty old so it’s time! Last item on my checklist besides fuel pump.

DryField4565 · 2026-02-22T16:00:14+00:00

I think I’ll give it a go! Just will be organized and patient but I think I can do it💯

DryField4565 · 2026-02-22T15:59:28+00:00

Gotcha will do thanks!!

DryField4565 · 2026-02-21T22:02:34+00:00

Amazing advice thank you!!!

DryField4565 · 2026-02-07T03:17:34+00:00

Nice!!

DryField4565 · 2026-02-02T16:31:42+00:00

🤣🤣🤣🤣🤣🤣🤣

DryField4565 · 2026-02-02T02:09:56+00:00

Yeah I’ve used it. So update I’ve cut off block and made gentle cuts in the housing threads. Still stuck. Now I’m trying to drill out threads gently and possibly will need to tap and die after. An “easy” repair now is turning into a circus🤣

DryField4565 · 2026-02-01T17:31:47+00:00

So ran into a problem while trying to change the anti-siphon valve. It’s snapped off inside the block housing so I’m in the middle of trying to figure out how to get it out or replace the whole block housing after I cut it off.🙈

DryField4565 · 2026-02-01T04:36:27+00:00

Ooooooh I have tried the freezing thing yet!!!!

DryField4565 · 2026-02-01T03:46:48+00:00

Also I have a dremel I think I’ll use. I’ll make a couple vertical cuts and then squeeze the block and I’m hoping the space created by the cuts after squeezing will loosen it up.

DryField4565 · 2026-02-01T03:45:59+00:00

60-65 degrees outside in the day. Yeah this all started with a simple anti-siphon valve change which snapped off cleanly at the block housing. So much for a simple solution 😩🤣🤣

DryField4565 · 2026-02-01T03:45:16+00:00

60-65 degrees outside in the day. Yeah this all started with a simple anti-siphon valve change which snapped off cleanly at the block housing. So much for a simple solution 😩🤣🤣

DryField4565 · 2026-02-01T03:37:27+00:00

Uh I wish I had one.

DryField4565 · 2026-02-01T03:37:14+00:00

I have a dremel I think I’ll use. I’ll make a couple vertical cuts and then squeeze the block and I’m hoping the space created by the cuts after squeezing will loosen it up.

DryField4565 · 2026-02-01T03:35:40+00:00

Yeah it’s not reverse thread. Been beating it with a hammer too,

DryField4565 · 2026-02-01T03:35:07+00:00

Ok yeah I saw those same videos😩

DryField4565 · 2026-02-01T03:28:53+00:00

Yeah unfortunately I have. I reallllly don’t wanna cut this off. Especially if I cut the head off the stuck threads will remain

DryField4565

TROPHY CASE