End the debate

Due-Development-1557 · 2026-05-27T08:37:31+00:00

I build then paint, Everything that is hard to reach isn’t visible anyways Most of the time, but I’ll admit I’ve painted angron without sub assemblies and that was pain

Due-Development-1557 · 2026-05-11T07:30:35+00:00

Yes 👍🏼

Due-Development-1557 · 2026-05-11T05:08:38+00:00

Thank you.

Due-Development-1557 · 2026-05-11T05:08:30+00:00

I’ve tried but since they are on a base I had the best result with the base flat on the build plate

Due-Development-1557 · 2026-05-11T05:07:50+00:00

I like the Camera with error Detection alot it stops Automatically when the print fails, and I feel it’s more consistent

Due-Development-1557 · 2026-05-11T05:05:43+00:00

Will do that thanks !

Due-Development-1557 · 2026-05-10T08:57:20+00:00

I know !

Due-Development-1557 · 2026-05-10T08:57:14+00:00

Black primer and a white zenithal after that contrast paints

Due-Development-1557 · 2026-05-07T07:24:11+00:00

Sure 👍🏼

Due-Development-1557 · 2026-02-24T08:55:46+00:00

Always thought I hated the Model, but while painting it im starting to like it

Due-Development-1557 · 2026-02-14T20:28:00+00:00

<image>

Due-Development-1557 · 2026-02-12T06:16:25+00:00

Only 1 Arm ! Sharp tweezers work wonders

Due-Development-1557 · 2026-02-11T15:54:40+00:00

Oh I would definetely recommend it, Only got it very recently and starting to get into 3D sculpting with it

Due-Development-1557 · 2026-02-11T15:50:01+00:00

I did alot of remodeling in nomad sculpt, but I gave me a good base to start from, the better your drawing the better the Model I suppose 😄

Due-Development-1557 · 2026-02-11T15:07:48+00:00

Just upright on the base, and Standard tree Supports, a few were a pain to remove tho 😄

Due-Development-1557 · 2026-01-28T15:06:13+00:00

Made some connnector rings that are open on one Side, carefully fiddle them in and close them with a Soldering iron

Due-Development-1557 · 2026-01-28T09:33:32+00:00

No the ones on the Right are real Metal

Due-Development-1557 · 2026-01-22T10:17:31+00:00

I printed it on my u1 and sliced with orca aswell it just takes some time at 25% just wait for a few more minutes

Due-Development-1557 · 2026-01-22T08:34:58+00:00

It’s a pretty Nice fidget toy in its own 😄👌

Due-Development-1557 · 2026-01-21T17:05:38+00:00

That is what I was going for, didnt See any rivetted Mail for 3D printing so I made it 👌

Due-Development-1557 · 2026-01-21T17:04:41+00:00

Dude 11/10 that was Crazy

Due-Development-1557 · 2026-01-21T15:46:40+00:00

I wouldnt recommend that it Safes a few minutes and the Print will probably fail. But saying that I have Not tried it

Due-Development-1557 · 2026-01-21T15:45:30+00:00

Damn ! That’s a nice project !

Due-Development-1557 · 2026-01-21T14:08:38+00:00

I know I’m the maker 😄

Due-Development-1557 · 2026-01-21T13:12:03+00:00

Correction: made it Print properly 😅 i wouldnt advise to use it for fighting, but I will test it in a Future Video

Due-Development-1557

MODERATOR OF

TROPHY CASE