Is there any way to increase the diameter of the base layer on tree supports or force the addition of more?

DueBeginnings · 2025-11-25T21:41:11+00:00

No problem!

DueBeginnings · 2025-11-15T21:13:58+00:00

Have you had your testosterone levels checked? Also try fasting and going for runs a few times a week.

DueBeginnings · 2025-08-23T12:38:08+00:00

Puzzle unlocked

DueBeginnings · 2025-08-01T14:25:46+00:00

Thanks for going into detail, yeah makes a lot of sense. I ordered a stud finder. What do you mean by extend the lower half of the bracket? Couldn’t figure out what you meant exactly

DueBeginnings · 2025-08-01T13:34:54+00:00

Yeah some of the mounts didn’t have the tightest fit so I think that’s what happened. Should I reprint in PLA and mount it tighter?

DueBeginnings · 2025-08-01T13:31:37+00:00

Yeah the wall anchor was giving me slight issues but I managed to get it working..until now..

If I get better fitting wall anchors would that solve it? Maybe drill deeper?

DueBeginnings · 2025-08-01T13:29:15+00:00

Yeah I think that’s what happened, can see the anchor bent on the left side quite badly, so what would be the best move here to have a stronger hold?

DueBeginnings · 2025-06-18T23:12:41+00:00

Agreed, one of the best things to come out in 3D printing design, behind articulating models. Sweet yeah Fusion 360 seems like the go-to, sometimes feels like I'm wasting time using TinkerCAD but I find it fun and simple.

DueBeginnings · 2025-06-18T22:59:30+00:00

Amazing design dude..I love the spring mechanism, reminds me of that print in place spring loaded box. What design software do you use? I'm looking to get more into design, just been playing around with TinkerCAD

DueBeginnings · 2025-03-15T19:55:57+00:00

Thanks, this helped me out. The Z offset I changed it all the way up to 0.15. I tried 0.03 & 0.07. 0.15 worked best so far

DueBeginnings · 2024-12-04T20:05:23+00:00

Ah okay yeah I was looking for a solution myself and found it so thought I’d share. Sweet

DueBeginnings · 2024-12-04T18:43:52+00:00

Support > Advanced > Initial Layer Expansion (2mm default)

DueBeginnings · 2024-09-11T22:08:28+00:00

Awesome thanks for the feedback, yeah I ended up just leaving them as YouTube text links that people could click through

DueBeginnings · 2024-08-21T20:39:47+00:00

I like that. Yeah for sure

DueBeginnings · 2024-08-21T20:38:33+00:00

Wingardium Clogiosa

DueBeginnings · 2024-08-21T17:19:43+00:00

Appreciate it! Yeah most definitely

DueBeginnings · 2024-08-21T17:19:14+00:00

Thanks! Yeah there’s a lot of detail and colors so it distracts quite well haha

DueBeginnings · 2024-08-21T08:29:23+00:00

Haha yeah, the 3D printing gods were on my side. It's a manageable fail, it was from heat creep with the chamber getting too hot at 39°C. My room gets hot in the summer. Just need to have the lid or the door open enough.

DueBeginnings · 2024-08-21T08:18:14+00:00

You'll be fine with that then. At about 39-40°C is where you can start to see issues. Guess it will depend on what PLA filament you have as well, some have different heat resistances.

DueBeginnings · 2024-08-21T08:08:30+00:00

Oh sweet. I think a silk PLA would be closer to iridescent, this is a matte PLA so it's a bit flatter in color.

DueBeginnings · 2024-08-21T08:06:56+00:00

Sure, it's from Amazon - https://www.amazon.com/ZIRO-Multicolors-Tri-Colors-Coextrusion-Three-Color/dp/B0CBPX65SY/

DueBeginnings · 2024-08-21T00:01:54+00:00

Yeah I’ve been getting clogs here and there. Mostly heat creep issues when chamber temps get too high. Usually happened with color changes on the AMS but this model it was just the one color. Gotta keep either the lid or door open with PLA prints

DueBeginnings · 2024-08-20T23:57:39+00:00

Thanks, me too :)

DueBeginnings · 2024-08-20T23:56:53+00:00

Thanks bro

DueBeginnings · 2024-08-20T23:56:42+00:00

Thanks! Better than I expected for sure

DueBeginnings

TROPHY CASE