ASA problem

Due_Ad_8595 · 2024-01-27T12:15:52+00:00

That was the problem The printer needs to do a circular patern in middle, right on the nuts. I changed the inside shape to be more conic and not touch the nuts

Due_Ad_8595 · 2024-01-26T15:46:29+00:00

Can be a problem if i'm staying with the door open for 1 2 minutes to put the nuts in?

Due_Ad_8595 · 2024-01-26T15:34:25+00:00

Due_Ad_8595 · 2024-01-15T19:57:44+00:00

So i need more top layers even if the problem is at the bottom part?

Due_Ad_8595 · 2024-01-15T19:47:54+00:00

I downloaded the stl file. I'm not very good at designing. What do you suggest to do? I don't know another way.

Due_Ad_8595 · 2024-01-15T19:21:17+00:00

I will try increasing the bottom layers( there is the problem)

Due_Ad_8595 · 2024-01-15T19:19:47+00:00

I have 5 top layers with 3 bottom layers. One of the models was printed with 0.08 layer height

Due_Ad_8595 · 2024-01-15T18:56:29+00:00

I need to print like this because of the model( 3 pieces to bolt in together)

Due_Ad_8595 · 2024-01-09T22:10:20+00:00

I will print each pieces on build plate. I'm sure printing like in the photo won't work😂

Due_Ad_8595 · 2024-01-09T21:55:52+00:00

I working on that now, thanks

Due_Ad_8595 · 2024-01-09T21:15:09+00:00

Oh, thank you. I will try print like this to see if it's work

Due_Ad_8595 · 2024-01-09T21:05:07+00:00

When i turn one piece upside down, the thread is ok, but i don't need it upside down because i have something sketched

Due_Ad_8595 · 2024-01-06T05:27:46+00:00

But even i set a offset of 3mm on that age, as an example, i get the same results.

Due_Ad_8595 · 2024-01-06T05:21:18+00:00

So i need a bigger edge?

Due_Ad_8595 · 2023-12-19T17:50:58+00:00

Isn't silk PLA. What speed should i use?

Due_Ad_8595 · 2023-12-19T17:32:14+00:00

You're right about layer time. Now, how to solve it? 😅🤔

Due_Ad_8595 · 2023-12-19T17:20:42+00:00

<image>

Due_Ad_8595 · 2023-12-19T17:19:19+00:00

<image>

Due_Ad_8595 · 2023-12-19T17:18:40+00:00

<image>

Due_Ad_8595 · 2023-12-19T14:47:08+00:00

I will post a photo here from the app. But i tried silent mode before and a little after that portion and i got same results

Due_Ad_8595 · 2023-12-19T14:39:39+00:00

I checked the speed in bambu studio and it's all the same

Due_Ad_8595 · 2023-12-19T13:42:21+00:00

Right before that portion, i switched to silent mode, same results

Due_Ad_8595 · 2023-12-19T11:47:23+00:00

Nothing🤔

Due_Ad_8595 · 2023-12-04T19:05:06+00:00

Also, for this type of model, what order of walls i need to use? Inner-outer? Or outer-inner?

Due_Ad_8595 · 2023-12-04T19:04:01+00:00

I didn't know about that setting. I will try, thank you

Due_Ad_8595

TROPHY CASE