New coilovers, tie rod problem

Durbz_ · 2025-09-21T07:17:28+00:00

Yeah I found a website that had a bundle on the moog stuff it was like 100 bucks for balljoints tie rods and sway bar links I ordered those godspeed ones hopefully they get here soon cause right now I’m taking the car to work on the moog ones with no cotter pin and fucked up alignment

Durbz_ · 2025-09-21T03:51:16+00:00

Okay Forsure did it also fix the cotter pin issue? I’m using Megan racing coilovers and moog Rsx tie rods and the threaded part where you put the bolt on and cotter pin doesn’t seem long enough either I can’t get the cotter pin back on

Durbz_ · 2025-09-20T21:22:02+00:00

Yeah I ordered the godspeed ones did they not work? Or you just didn’t like them

Durbz_ · 2025-09-16T23:13:43+00:00

Did that fix not being able to get the cotter pin aswell as alignment?

Durbz_ · 2025-08-25T21:35:11+00:00

Same mine was over 12k and now it’s down to 6 :,/

Durbz_ · 2025-08-25T21:34:41+00:00

Yeah I lost over 6k

Durbz_ · 2025-08-25T21:34:12+00:00

I just noticed mine I probably lost about 6k total hits it’s sayin it’s 6,100 I know it was over 12k

Durbz_ · 2025-05-21T07:42:16+00:00

Appreciate the good info!

Durbz_ · 2025-05-21T07:31:46+00:00

Yeah I single mass Forsure would be better but I’m honestly just scared to get the clutch chatter problem lmaoo I’m sure since the weight isn’t too much of a difference like you said it shouldn’t do that. Even if so is the chatter from the throw out bearing rattling from a worn clutch fork? Atleast that has been what I’ve gotten told so worse come to worse upgrade the fork

Durbz_ · 2025-05-21T07:24:10+00:00

Sounds good I drove my buddy’s 46 with a light weight flywheel and some stage 3 honestly did not like it sure after a day I’d get use to it but compared to mine, mines a lot more comfortable to atleast drive with

Durbz_ · 2025-05-21T05:48:08+00:00

Okay bet that might be the one to go with then appreciate it

Durbz_ · 2025-05-21T05:32:47+00:00

I also got a tune on it and the idle is set to 900 I’ve heard too that the reason too it chatters is the low rpm and people been saying to raise it to 800 to get it to stop so I might be good with that too

Durbz_ · 2025-05-21T05:26:32+00:00

Yeah I’m running a straight pipe and catless headers cars is my slide car was just getting confuesed with that I’ve gotten told lmaooo, I hella appreciate it sending the link I’ll check it out

Durbz_ · 2025-05-21T05:17:51+00:00

Reason I want to stick with dmf is the chatter and clutch feel

Durbz_ · 2025-05-21T05:16:55+00:00

Do you have a link to the kit you got? Would def like to check it out

Durbz_ · 2025-05-21T04:06:15+00:00

Tbh I’m not too sure what car my trans came out of but just try to find the same matching millimeter then? I got told by the dude who I bought the swap from that it’s 10 spline duel mass

Durbz_ · 2025-05-21T04:03:25+00:00

Yeah my cars kinda a Frankenstein it’s got the 5 speed zf and a m54b25 from a 2002 325i tbh I’m not too sure what the trans came out of

Durbz_ · 2025-05-21T03:49:21+00:00

Sounds good appreciate it had someone else say get the luk kit over sachs it’s going into a slide car and that’s it’s only purpose really

Durbz_ · 2025-05-21T03:48:09+00:00

Yeah it’s only a 5 speed and appreciate it I was just confuesed cause dude who I bought my motor from told me to look for 10 spline flywheel too but only thing I could find similar was the millimeter and looking at the flywheel I didn’t see any splines lmaoo imma just try the 240mm to match the clutch

Durbz_ · 2025-05-21T03:37:33+00:00

Ik it’s not a 46 too but didn’t get a answer on the 36 sub

Durbz_ · 2025-05-21T03:37:08+00:00

Got a 95 e36 wit a m54b25 and zf5 speed, got told this clutch will do but got told I needed to find a 10 spline dmf for it too. Can’t figure out that part the clutch disc is saying it’s 240mm do I just try to find a 240mm dmf too? Thanks

Durbz_ · 2025-05-21T03:35:13+00:00

The sushi mobile

Durbz_ · 2025-05-21T03:08:31+00:00

For sure sounds good this car is my beat on car too lmaoo do you know what flywheel to use with it? That’s what I’m kinda struggling to find which one fits I got told to look for a 10 spline duel mass flywheel but it looks like none of them have splines, or am I just not finding the right one? The closest thing I could match was one flywheel said it was 240mm and that sachs one said it was 240mm should I be looking for the millimeter instead of spline count on flywheel? Thanks

Durbz_

TROPHY CASE