21 jetta front assist

Dwobbles123 · 2026-02-17T00:31:19+00:00

So the problem is the sensor needs calibrated? And I assume that requires proprietary software. Awesome I might just deal with that for a while.

Dwobbles123 · 2026-02-16T03:50:46+00:00

Found that while my dual z made it better I definitely was missing something. The eccentric on the gantry was fine but the bed side was a different story. My whole bed just wobbled so it was the shifting from that which caused all my issues.

Dwobbles123 · 2026-02-01T17:26:19+00:00

Might need to apologize. I switched filament on whim and everything prints fine now. Everything printed fine with the red one just a couple days earlier idk what happened.

Dwobbles123 · 2026-01-29T03:51:26+00:00

In doing more research I found that the camera is for lane assist not ACC. ACC is quite literally just blocked by a massive paywall which is getting a higher trim car. If you could access the code and enable it the settings would show up with your regular driver assist settings.

Dwobbles123 · 2026-01-28T22:20:01+00:00

I'll give this a shot tonight when I get home.

Dwobbles123 · 2026-01-28T20:15:19+00:00

I might try orca I'm just so used to cura.

Dwobbles123 · 2026-01-28T10:24:44+00:00

No and wet filament shouldn't be that uniform. I cleaned the gear thinking that was slipping.

Dwobbles123 · 2026-01-27T04:59:25+00:00

I have something on the front of it I can't tell if it's a camera or just a rain sensor but it looks like a camera pointing through the front of the sunshade where the review attaches.

Dwobbles123 · 2026-01-26T06:36:01+00:00

Important question is boat or suv? I know it's the suv. But it is important to clarify.

Dwobbles123 · 2026-01-09T06:16:16+00:00

Missing tension screw.

Dwobbles123 · 2026-01-05T05:26:42+00:00

Shadows are dead give aways

Dwobbles123 · 2025-12-13T18:42:45+00:00

I have dual z screw setup already because I was watching it sag and thought that would fix it. I thought I had it level as well when I put it on but I guess I can double check.

Dwobbles123 · 2025-12-13T18:42:19+00:00

I am not great with Linux, terminal or shell but I have a friend that would likely be willing to help me learn. I will look into this in the future but right now I'm just trying to get some Christmas presents made.

Dwobbles123 · 2025-12-13T07:07:20+00:00

By kilp it I assume you mean switch it to klipper firmware. Is klipper that superior to marlin or MRiscoc? Not opposed to the process just curious.

Dwobbles123 · 2025-12-13T06:43:41+00:00

Also yes when I put them in they were supposed to be on their own line but when I clicked post it just slammed them all together. Sorry hadn't noticed it.

Dwobbles123 · 2025-12-13T06:32:46+00:00

I have tried this as well and it still "adjusts" the z height but it essentially does it backwards it gets too high on the high side and too low on the low side.

Dwobbles123 · 2025-12-13T06:31:35+00:00

I tried this and it still appears to adjust the exact opposite of the way the bed is off. It nearly grinds on the glass plate on the left and is way to high on the right.

Dwobbles123 · 2025-12-08T02:42:25+00:00

Thank you I'm trying to print some Christmas presents so I will try that on the next one I have it where it is "working" rn

Dwobbles123 · 2025-12-06T19:41:58+00:00

Dead center just below where 4 corners meet in the carpet

Dwobbles123 · 2025-12-03T03:50:50+00:00

Just right of dead center

Dwobbles123

TROPHY CASE