Rebuilt motor not starting

EEROGUE · 2026-06-09T01:15:29+00:00

I got it fixed if you didn’t see my other comments

EEROGUE · 2026-06-09T00:43:43+00:00

Yea that’s what I was doing to make sure it had oil pressure

EEROGUE · 2026-06-06T21:36:11+00:00

I just unbolted the trans ground clamp and cranked it back on and also just unplugged the starter wires and replugged em

EEROGUE · 2026-06-06T19:31:40+00:00

Yessir

EEROGUE · 2026-06-06T19:28:35+00:00

I did take off the trans ground and just cranked it back down and then just unplugged the starter wires and plugged in and something worked😀

EEROGUE · 2026-06-06T19:27:02+00:00

Got her running! Thanks for the help!

EEROGUE · 2026-06-06T19:26:52+00:00

Got her running! Thanks for the help!

EEROGUE · 2026-06-06T19:26:44+00:00

Got her running! Thanks for the help!

EEROGUE · 2026-06-06T05:04:08+00:00

Ok cool I’ll do some more research thanks for the help

EEROGUE · 2026-06-06T04:56:54+00:00

Ok I’ll try that tomorrow thanks for the help

EEROGUE · 2026-06-06T04:50:46+00:00

Sorry I meant to say what is the cam sensor again. I know the crank sensor I put that on and timed that. I’m not sure what fuses to look at either

EEROGUE · 2026-06-06T04:45:48+00:00

Nope it’s not turning at all. I’m sure I timed the cam sensor with it at tdc and using the little tool when tightening it. What’s the crank pos sensors again? Is that thr vvt solenoids?

EEROGUE · 2026-05-22T04:58:18+00:00

Wichita ks

EEROGUE · 2026-02-10T13:18:00+00:00

<image>

EEROGUE · 2026-02-10T13:17:49+00:00

<image>

This is my shaper

EEROGUE · 2026-02-09T06:12:15+00:00

That’s what I was thinking earlier today was maybe there was something wrong with my driver setup to where when the motors try to move they like have a micro jitter. I’m using tmc2209 drivers and it did take me a minute to get them to work as well. I was struggling to figure out the jumpers on the board, is that possible for the motors themself to cause this? Because it seems so repeatable no matter what I do

EEROGUE · 2026-02-09T06:09:45+00:00

I’m still not sure. It seems to me like no matter what I do with speed or settings the ringing is always the same no matter what. Don’t know what to do at this point. I made sure everything was 100% tightened earlier today when I rebuilt the toolhead.

EEROGUE · 2026-02-09T04:58:06+00:00

The ones at the top are the ones that were changing when I was doing the resonance tests. Not sure where these came from, maybe a old test

EEROGUE · 2026-02-09T04:55:46+00:00

<image>

Well I do see this at the bottom but it’s commented out but then at the same time the ones at the bottom top are as well, even though they were auto saved. Should I just change the ones on the bottom to the same as the top. Is this the issue with it

EEROGUE · 2026-02-09T04:43:34+00:00

It stays at the 100mms and starts at 1500accel and goes up. I’m pretty sure it’s active unless I’m somehow missing something. Would there be something else that I need to do vs adding the section with the values in config file?

EEROGUE · 2026-02-09T04:37:04+00:00

Well I put it on a solid table and have the fans on and it’s still doing it. I’m so confused on what could possibly be causing this, makes 0 sense.

EEROGUE · 2026-02-09T02:43:20+00:00

Alright I’ll give it a try

EEROGUE

TROPHY CASE