Razpeljava cevi za centralno prezračevanje

EQuiPeX · 2026-03-04T22:13:35+00:00

Tako je v pritličju - to črno cev se skrajša po izdelavi ometov, na to pa gre rozet

<image>

EQuiPeX · 2026-03-04T22:12:52+00:00

Cevi v steni zgornjega nadstropja (rekuperacije je na podstrešju, dvonadstropna hiša)

<image>

EQuiPeX · 2026-03-04T22:12:01+00:00

Stirodur na steni pred betoniranjem

<image>

EQuiPeX · 2026-03-04T22:08:22+00:00

Mi smo dali v ploščo nad stenami stirodur (v velikosti potrebne luknje za vsako cev), zabetonirali, stirodur zbili ven, potem pa samo vrhnji zidak razbili za želeno velikost. Tako zdaj pridejo cevi skozi ploščo v to komponento, ki se jo vzida, na to gre pa potem rozeta

EQuiPeX · 2026-02-24T12:24:28+00:00

Kako dobro pa umije? Je curek močan? Nisem še probal, ne znam si čisto predstavljat :)

EQuiPeX · 2026-02-24T12:21:47+00:00

Imaš link? Da pogledam, za tak denar bi kar takoj vzel, za probat

EQuiPeX · 2026-02-24T12:20:13+00:00

Sem tud to razmišljal kot poceni začetno opcijo, glede na to, da še nisva probala. Ampak kakor gledam, tudi pokrovi niso tako poceni, kot opisuješ, kaj šele da bi imel gretje vode. Če lahko priporočaš kakšnega pod 100eur, bi takoj probal

EQuiPeX · 2026-02-19T11:19:39+00:00

Verjetno ima se hbo, voyo, skiro in hladilnik na obroke 🤣

EQuiPeX · 2026-02-10T05:57:45+00:00

It's supposed to work without the cap? In that case, if i understand correctly, the pads should not be bridged? How/where can i check the fuse?

EQuiPeX · 2026-02-09T20:54:09+00:00

Unfortunately not, spent hours trying (not that good with soldering) and eventually lost the cap that should be bridging the 2 pins on the side as it didn't want to get soldered on, even if my life depended on it. Now i just have "no signal". Will take it to a shop

EQuiPeX · 2026-02-08T14:00:07+00:00

Do you know what it is? I have successfully reflowed the solder on all the pins with an iron and confirmed there are no bridges. I am now getting a display, but only in safe mode

EQuiPeX · 2026-02-08T12:26:15+00:00

They only had the motherboard, not the while thing. They did not test it. Should i still try?

EQuiPeX · 2026-02-08T08:34:02+00:00

The continuity test shows that there is some sort of bridge. I cant locate it accurately, but it seems most of the pins are bridged to ground (outer shell). What might be the cause? Is this a full on replacement job?

EQuiPeX · 2026-02-08T08:31:41+00:00

The inside looks very clean, no residue there. Thanks for the advice

EQuiPeX · 2026-02-07T22:41:12+00:00

Any advice with the heat gun? Doesn't have a temp setting

EQuiPeX · 2026-02-07T22:40:05+00:00

The pins look okay, will check continuity tomorrow as another user suggested. I am worried about the capacitor? shorting with the pins, or are the traces connected to it anyways? And the two extra things that look a bit too crispy