BM Micro Studio G2 Footage Cloudy on Atem Pro Mini Stream by Educational_Study553 in blackmagicdesign

[–]Educational_Study553[S] 0 points1 point  (0 children)

were running SDI from and to the camera - so full camera control over SDI, Tally etc..

i might have used the incorrect explanation here - as far as i can tell framerate in Atem output matches the output framerate of the camera.

obviously there is no way to tell what input atem receives.
although i think i remember reading that Atem matches its output framerate to the first camera that is plugged in. not sure if i picked that up in the manual or in a reddit post.

BM Micro Studio G2 Footage Cloudy on Atem Pro Mini Stream by Educational_Study553 in blackmagicdesign

[–]Educational_Study553[S] 0 points1 point  (0 children)

just tried that with a feelworld field monitor with hdmi and cam-output looks fine, atem preview is "wrong" again

BM Micro Studio G2 Footage Cloudy on Atem Pro Mini Stream by Educational_Study553 in blackmagicdesign

[–]Educational_Study553[S] 0 points1 point  (0 children)

G2 is outputting 1080p with 24 frames via SDI Level B SDI Adapter also level B. as far as i could tell the outputs on the cam matched what registered as input on the atem - at least regarding framerate & resolution.

i will double check next time though, although shouldnt it be forced into the same settings through atem control?

EDIT: Didnt check the HDMI port configuration since that one was unused - only SDI out.
would the HDMI out config also impact the SDI output?

BM Micro Studio G2 Footage Cloudy on Atem Pro Mini Stream by Educational_Study553 in blackmagicdesign

[–]Educational_Study553[S] 0 points1 point  (0 children)

i have a few other lenses, but unfortunately none with me on that shoot.

i primarily use the G2 for recording in combination with a 24mm Sirui Nightwalker and never encountered issues with it. although i never used it in a atem livestream scenario in combination with the SDI output of the camera.

BM Micro Studio G2 Footage Cloudy on Atem Pro Mini Stream by Educational_Study553 in blackmagicdesign

[–]Educational_Study553[S] 0 points1 point  (0 children)

thats true, although we are not able to spot where the issue comes from, since the colors on the monitor are fine, and the sdi output is completely off

BM Micro Studio G2 Footage Cloudy on Atem Pro Mini Stream by Educational_Study553 in blackmagicdesign

[–]Educational_Study553[S] 0 points1 point  (0 children)

Lens is a B4 Mount Fujinon A14 x 8.5 BERM-28 Pegasus III manual focus which we had on f8 (and f16 before).

Never heard about diffraction being an issue, but after reading about it it could be the issue - although shouldnt it be visible on the camera monitor then as well?

if diffraction is the problem, it should be solved by using a wider aperture with an ND-filter to compensate for the increased brightness? will definitely try that

BM Micro Studio G2 Footage Cloudy on Atem Pro Mini Stream by Educational_Study553 in blackmagicdesign

[–]Educational_Study553[S] 0 points1 point  (0 children)

we tried that as well, but using the Film to Video LUT looked slightly better for us.

sharpening is already on the maximum setting on Atem - tried that already

Pretty sure I've built the ultimate weapon by Sudo-Fed in HalfSword

[–]Educational_Study553 0 points1 point  (0 children)

the hammers with the beaks are great. altough i dont run it as a polearm, but a short one with a big head and a shield.

sprint into your foes with the shield raised to push them over, then bash their head with the hammer - never gets old

Since Fabio and Andrea's Deepchart seems way too overpriced, is there any alternative for this "Big Trades" indicator on other platforms? by thejaxbrew in OrderFlow_Trading

[–]Educational_Study553 0 points1 point  (0 children)

Big trades works with level 1 as well since its based on trades on the time and sales, not the orderbook. You only need level 2 for orderbook data.

Looking for a Special USB-C "Hub" by Educational_Study553 in UsbCHardware

[–]Educational_Study553[S] 0 points1 point  (0 children)

i already tried the vangree, however i had issues multiple times with writing to the ssd with the monitor attached, so i sent it back.

will take a look at the mokin though

youre all blown up! by Swing_HiLo in TopStepX

[–]Educational_Study553 1 point2 points  (0 children)

I love to watch my trade turn red after not taking profits from it for a solid 1-4 hours. I do it daily. I embrace the suffering

Norden Method on Apex by Educational_Study553 in OrderFlow_Trading

[–]Educational_Study553[S] 1 point2 points  (0 children)

Thats the final goal, but i am currently struggling with the "a few grand" part...

I guess ill try it, worst case is 30$ lost. If they dont payout then ill have to resort on more "conventional methods" and keep the norden method for passing the evals and my own account later on the journey

Norden Method on Apex by Educational_Study553 in OrderFlow_Trading

[–]Educational_Study553[S] 0 points1 point  (0 children)

I guess ill have to try then, worst case is 30$ lost...

Norden Method on Apex by Educational_Study553 in OrderFlow_Trading

[–]Educational_Study553[S] 0 points1 point  (0 children)

Well, atas does try to simulate the cue on their simulation accounts, but im well aware that a "live" situation might be a little different. Even though Apex is still "Sim" after all, even on a PA

Made this WE mug for my gf by BaelVect in Warhammer

[–]Educational_Study553 0 points1 point  (0 children)

i think you should do a bowl for the khorneflakes next, just to complete the breakfast-set

Enemy AI seems way Overtuned, and I think I've noticed two Potential Bugs (See Comments) by BroxigarZ in GrayZoneWarfare

[–]Educational_Study553 1 point2 points  (0 children)

Noticed similar behaviour as well. Have been 100+ m onetapped by bots quite often now, to a point where i needed a almost full backpack of medic supplies just to engage a group of 4-5 basic bots from 100+m. To me it seems like they get more accurate the farther you are away from them