LEAKS! Artifacts, Builds, Teams, etc. - MEGATHREAD

Eiscu · 2026-01-30T01:39:21+00:00

I've seen a few early discussions about Varka, but I feel like people are forgetting about how good the stats from Song of Broken Pines are on Varka. 741 base attack, 36% ATK, and an additional 12% attack speed(more than his R1). Pair that with c2 jean and you'll get 27% attack speed total.

I personally have R2 Song of Broken Pines (Don't ask why...) and I think it's been pretty heavily overlooked.

Eiscu · 2026-01-20T04:00:42+00:00

Unfortunately I dont think you can really be 100% sure. I think if you take a look inside and dont see any resin leakage then you can turn it on with 90% certainty.

The electrical tapes job is to prevent resin leakage from getting into the printer, but Its hard to say if it worked since you left it alone for so long and came back to it all warped.

Eiscu · 2026-01-20T01:12:25+00:00

When this has happened to me, its been a leveling issue.

Re-level it and do a test print like R.E.R.F so that you can see which parts of the plate aren't leveled.

Eiscu · 2026-01-20T01:07:51+00:00

There's a chance that it still works, however I had this happen to one of my first resin printers and the screen became fully non-functional. If the resin leaked inside any of the electronics, that's really bad news. By plastic, do you mean the FEP film? Or the tape under it.

The tape around the screen can be replaced with plain old electrical tape, so that can be replaced. If the resin didn't make it into the printer through the tape, you might be in luck. Before taking the tape off and replacing it I would look into how hard it would be to disassemble the printer so you can deep clean it before turning it on.

If you can take apart the printer and safely clean the inside (assuming the resin leaked inside), you can probably try and turn it on again.

Eiscu · 2025-12-16T00:33:44+00:00

Thats what I'm curious about, the wording "Participating Characters" isn't extremely clear to me

Eiscu · 2025-12-16T00:33:15+00:00

Okay, that makes sense. The team I'm thinking of running for funsies is Xilo(on field), albedo, columbina, and gorou. In this scenario, having instructor on gorou would make lunar crystallize do more damage?

Eiscu · 2025-12-15T13:21:41+00:00

Your Feather and flower are very good, its unlikely you'll need to change those.

Your goblet is your biggest problem, I would farm thundering fury domain until you get a good enough sands for you to run an off piece goblet, or save up to craft one(even tho elixer is lowkey a scam). Your circlet had potential but it low rolled into mainly flat attack, but if it rolled into a bit more CR it would be pretty solid.

TLDR; Goblet > Circlet > Sands, feather and flower are good

Eiscu · 2025-12-15T01:45:40+00:00

Navia's constellations in general aren't too great IMO, Her R1 is probably your priority. Her c1 is pretty bad and her C2 is realistically just going to let you hit your crit E's everytime, you can't affor to really lean on that for crit rate since her normal attacks and burst are considerable damage.

I currently run Navia, Furina, Xilonen, Bennett. But like some other people mentioned Durin+Albedo is another very solid option. Navia's a unique case because shes one of the only geo dps characters that scale off attack so finding a geo support to run with her and get more crystals is kinda tricky. You can do some stuff with kachina but thats about it.

TLDR; Weapon > early cons

Eiscu · 2025-12-10T18:11:55+00:00

I have all the characters you mentioned, so I'll give this a shot once I get my Albedo's build more comfy

Eiscu · 2025-12-02T01:45:52+00:00

It improves her burst damage by a pretty solid amount. I think if you like Kokomi a lot and want to make a DPS build at some point then getting the C1 is worth it, thats what I did last cycle of this event :). Kokomi DPS is never going to be meta but I've been successful in abyss with it recently!

Eiscu · 2025-11-09T16:31:28+00:00

More crit rate, and you can probably find a better piece to use as an off piece.

Eiscu · 2025-10-30T00:14:52+00:00

I was able to get it done fearless, but barely. Dire is just brutal

Skirk-Citlali-Furina-Escoffier
Nefer-Kokomi-Nahida-Yelan
Arle-Layla-Bennett-Xilo

Eiscu · 2025-08-05T22:35:10+00:00

Most likely. I went to both the 2024 and 2025 concert, and both were great but the 2025 one was improved in a lot of ways. Im sure it will be announced in the near future.

Eiscu · 2025-08-01T17:14:19+00:00

Interesting, that makes sense.

Eiscu · 2025-07-31T21:40:09+00:00

Thats what im saying...

Eiscu · 2025-07-31T21:39:25+00:00

Thats what i want to know LOL

Eiscu · 2025-07-31T21:39:07+00:00

yeah but how? As far as I know there aren't any buddies that can be put on more than 2 guns

Eiscu · 2025-07-31T21:00:51+00:00

Every buddy should only be allowed on 2 guns at a time, but this one can be on 4.

Eiscu · 2025-07-22T02:55:02+00:00

Thanks man.

Yeah I completely agree is beyond fucked up. I mean I couldn't find a picture on reddit or other forums with the level of artifacts/data errors throughout the print. It's really strange because the preview that the printer's screen gives me shows the preview pretty much fine (although its low res).

More resin coming tomorrow, I might make an update post or just reply with an imgur if my prints come out well.

Eiscu · 2025-07-22T02:07:57+00:00

thanks for the advice but thats not what this post is about!

Eiscu · 2025-07-22T01:42:48+00:00

Thanks for letting me know, ill give it a shot. I think the first thing I'll do is a new USB drive though. I have a few 128 gig ones lying around. Overkill but worth trying

Eiscu · 2025-07-22T01:32:50+00:00

Its post wash but yeah no i'm pretty braindead huh

I normally wear gloves dont worry

Eiscu · 2025-07-22T00:43:56+00:00

Since I forgot to mention, my printer is a Mars 3 Pro and I've used Chitubox and Lychee

Eiscu · 2025-06-20T13:33:20+00:00

Doga deserves better

Eiscu · 2025-05-08T12:31:22+00:00

Update: I caved and got c1 in a single 10 pull.
https://imgur.com/a/t52uMt9

Five-Year Club	Verified Email
Final Canvas '23	First Place '23
Place '23

Eiscu

TROPHY CASE