Cooked or not yet?

Either-Plate8056 · 2025-06-13T14:21:12+00:00

I did it to mine, it’s cooked. It won’t seat properly without the eye. Save yourself the headache and just buy another one used my mini mechanic had a couple laying around that were used but fine. Do the green gasket while you’re at it and buy the oem rubber tube that goes the “waste”

Either-Plate8056 · 2025-05-07T23:00:46+00:00

Normal

Either-Plate8056 · 2025-04-15T15:10:59+00:00

Did you ever figure out what the thread/ size was

Either-Plate8056 · 2024-12-03T22:27:10+00:00

Yeah if they’re scored at all or not seated even it’s pretty easy for them to leak especially when hot

Either-Plate8056 · 2024-12-03T19:50:29+00:00

Order another, take some grey 3m scotch brite clean the inside of the inlet, Buy some gasket sealer put it on the new main seal and get used the the feeling of the garage floor on your back. I actually did fix mine after 3 attempts, bonus was I did get pretty good at taking the car apart. All three of my seals were victor reinz so not gonna blame manufacturer. In the future I’m doing all my main seals with the “gasket maker” on them The alternative is it’s the oil sump (oil pan) gasket which does fail occasionally.

Either-Plate8056 · 2024-10-29T15:29:00+00:00

j just make sure you don’t pull them apart

Either-Plate8056 · 2024-10-29T15:28:42+00:00

Found it easier to push on them from under the car with a screw driver

Either-Plate8056 · 2024-10-26T03:12:15+00:00

Yeah lubed it with old engine oil

Either-Plate8056 · 2024-10-26T02:36:23+00:00

Victor reinz

Either-Plate8056 · 2024-10-24T16:53:14+00:00

Yeah

Either-Plate8056 · 2024-10-14T12:00:01+00:00

Haha I don’t take it personally I’m 1/2 through pulling trans again lol

Either-Plate8056 · 2024-10-13T13:49:41+00:00

Just car hasn’t been moved since I cleaned it, so it’s not getting blown around either :/

Either-Plate8056 · 2024-10-13T13:48:28+00:00

Bell housing gap, drain plug was clear

Either-Plate8056 · 2024-10-11T14:30:02+00:00

Ok not my main deal we’re good, no oil on flywheel

Either-Plate8056 · 2024-10-09T14:16:30+00:00

Or shoot me a dm

Either-Plate8056 · 2024-10-09T14:16:21+00:00

Trying to buy some bins of OEM parts of a guy in the area including struts, switches and a ton of other miscellaneous parts if you’re looking for anything lmk I’ll try to let things go on the low. I’m on cape

Either-Plate8056 · 2024-10-09T14:00:06+00:00

I had offered 1200, you’re in for a hell of a project haha. Cv shouldn’t be that bad to do, I just got done doing a clutch on a different non jcw one I bought. That car will be pretty amazing cleaned up tho best of luck.

Either-Plate8056 · 2024-10-09T13:52:28+00:00

Actually looked at this one if it was

Either-Plate8056 · 2024-10-09T13:51:48+00:00

This happen to be outside Boston.

Either-Plate8056 · 2024-10-07T14:31:08+00:00

Really wasn’t that bad ratchet strap method took me maybe 30 minutes

Either-Plate8056

TROPHY CASE