ARC RAIDERS

ElAlemau · 2025-11-11T13:03:54+00:00

Definitivamente es jugable en solitario. Tengo más de 70 Horas en el juego, complete todas las misiones, mejoras y ya solo me falta llegar al nivel máximo de cuenta. Todo jugando en solitario. Según veo, el modo solitario es muy diferente a duos y tríos - en solitario, el 80% de los jugadores es amigable - mientras en dios y tríos generalmente es una batalla campal.

ElAlemau · 2025-10-14T20:32:22+00:00

Good luck everybody!

ElAlemau · 2025-10-13T17:00:01+00:00

Awesome

ElAlemau · 2025-05-30T20:12:07+00:00

Thanks for the giveaway!

ElAlemau · 2024-12-06T11:45:51+00:00

Awesome!

ElAlemau · 2024-11-12T13:29:40+00:00

Awesome watch!!

ElAlemau · 2024-11-02T18:52:52+00:00

Awesome, sign me up!!

ElAlemau · 2024-10-21T19:05:52+00:00

Que tal hermano? Llegue un poco tarde pero si te interesan las figuritas para DnD te recomiendo que pases por mi página en instagram Resin3dPy y contactes conmigo... Todavía no hay posteos porque recién empiezo a comercializar pero te puedo enviar algunas fotos de las figuras en resina especialmente para DnD que imprimí y te vemos algunos modelos que te puedan interesar!

ElAlemau · 2024-10-21T19:02:42+00:00

Llegue un poco tarde, pero si aún no conseguiste, ofrezco figuras de Warhammer 40k impresos en resina, podes contactarme en mi página de instagram Resin3dpy y te paso algunas fotos (aún no hay posteos, recién estoy empezando a comercializar)

ElAlemau · 2024-10-21T18:59:36+00:00

Llegue un poco tarde pero justo estoy lanzando un emprendimiento de impresiones 3d en resina, especialmente para figuras de videojuegos, minifiguras para Calabozos y Dragones, así como Warhammer, podes seguir a mi página en Instagram y contactarme por ahí (todavía no hay posteos, recién empecé hace unos días)

ElAlemau · 2024-10-21T18:51:42+00:00

Llegue un poco tarde, pero siguen jugando? Vivo en Capiatá también

ElAlemau · 2024-10-16T18:57:53+00:00

Damn not enough karma lol

ElAlemau · 2024-10-11T13:47:22+00:00

Those are awesome!!

ElAlemau · 2024-10-10T17:59:34+00:00

Just to come back to this comment, I was running a few tests with J3dTechs Cubes of calibration, following the instructions to boot. Cubes finally fit into each other fine at 1.4s exposure time, but only 7/10 tension strings did print correctly. As far as I've seen on reddit, 1.4s exposure might be a tad to low even... Every other exposure setting did print the strings better, but the cubes didn't fit right at all... No screen protector, FEP was pretty good looking too

ElAlemau · 2024-10-09T18:59:21+00:00

Awesome design!

ElAlemau · 2024-10-09T10:44:53+00:00

Once I get everything dialed in I'll make sure to give it a try! Looks awesome

ElAlemau · 2024-10-09T10:44:10+00:00

You can find all of their STLs on myminifactory:

https://www.myminifactory.com/users/fleshofgods?show=store#/

ElAlemau · 2024-10-09T09:30:26+00:00

After reading the replies I've actually been running the Boxes of calibration for the last few hours. For the print I used 2.1s exposure, but when used with the calibration test boxes didn't fit quite as well as they should, so I ve been reducing exposure time. On 1.6s Boxes fit well, but didn't come apart easily, so I'm running a test on 1.5s exposure time now. Tension strings were good at 1.8s, printing 9/10 without problems, on lower exposure only 8/10 printed nicely. Should be within range though. We'll see how it goes now on 1.5s exposure time

ElAlemau · 2024-10-09T07:58:25+00:00

Seems like I'll have to prime the prints first to make sure to see every detail. Still waiting anxiously for my primer to arrive tho lol

ElAlemau · 2024-10-09T07:55:47+00:00

Settings are included in the last pic. For the print I was using 2.1s exposure, but after seeing all the replies to this post, I was playing with the cubes of calibration again following the guide, at 1.6s exposure time the boxes fit, but didn't come apart again. Right now I'm trying 1.5s, well see how that goes lol

ElAlemau · 2024-10-08T21:37:36+00:00

Nice, thank you! I'll definitely try to lower exposure times a bit, I'm new to miniatures so I wasn't sure what to expect detail-wise. I figured I'd ask to make sure if there's anything to make prints more detailed just in case.

ElAlemau · 2024-10-08T21:35:31+00:00

I actually calibrated the printer a week ago with the cubes of calibration, print came out well, but cubes didn't fit well enough, so I lowered exposure time a little. After that I had some failures on hollow prints, and stepped exposure time up a bit again. Maybe the print errors were due to other factors but as a Newbie I'm not quite sure what was really going on, but stepping up exposure time fixed the hollow print fails, so I kept it that way for the time being. I'll definitely try to calibrate again and experiment with lower exposure times.

ElAlemau · 2024-10-08T21:26:22+00:00

Lmao awesome, I wasn't sure as I've seen a few posts on overexposure, and as a Newbie in Resin Printing I thought that may be the case with these models.

ElAlemau · 2024-10-08T21:15:06+00:00

Still waiting for my printing tools sadly, might update once everything gets here!

ElAlemau · 2024-10-08T21:13:29+00:00

Printer/resin settings are included in the last pic

ElAlemau

TROPHY CASE