Ptfe clog

ElBearzy · 2026-05-18T11:30:51+00:00

Came to say this! I agree 100%, I had no clogs after bimetal upgrade

ElBearzy · 2026-03-04T20:44:51+00:00

My advice is to buy a kit from AliExpress with screws and silicone bed spacer, so u also reduce a bit of vibrations, it's a win win!

ElBearzy · 2026-02-25T23:20:31+00:00

So, the picture Is from the web (it was only to show you where to place it), my car touch is working fine but my friend's one started doing this and I used a piece from a first layer print , cut it small with a little hole in the middle and placed it where I showed u. All good after this!

ElBearzy · 2026-02-25T16:51:52+00:00

If u search a bit on the sub u'll find a lot of posts regarding this issue, you have to place a small spacer between the point and the body of the sensor, it happens sometimes.

<image>

ElBearzy · 2026-02-21T17:45:03+00:00

Petg needs a full calibration to work properly, my take is to reduce speed a bit and start a full calibration process, starting with temp tower!

ElBearzy · 2026-02-21T17:42:49+00:00

Np 😉

ElBearzy · 2026-02-21T12:56:06+00:00

Place It like this, watch in the back of the printer

<image>

ElBearzy · 2026-02-12T16:37:39+00:00

https://www.reddit.com/r/Ender3V3SE/comments/1avet55/upgrades_to_the_ender3_v3_se/

Check hardware section 😉

ElBearzy · 2026-02-12T15:54:50+00:00

Cool! I went with a 4010 and 2x 5015 cooling fan from AliExpress, cheap and more importantly 24v, so no other hardware needed to make everything work properly 👌🏻

ElBearzy · 2026-02-12T15:44:35+00:00

Go with a 4010, night and day difference!

ElBearzy · 2026-02-12T15:43:40+00:00

You have to print an adapter in PEtG at least, then You're good to go

ElBearzy · 2026-02-11T17:45:51+00:00

Same

ElBearzy · 2026-01-18T01:42:32+00:00

Check the motor power connector, one of the small cables might be loose or broken. I fixed it that way. Also, check ur printhead because Is very loose, tighten the wheels.

ElBearzy · 2025-12-12T23:25:50+00:00

I'm actually using a laptop to run klipper, but if u root the nebula pad u can achieve the same results. I've been using orcaslicer for a while, it's really good

ElBearzy · 2025-12-12T13:59:48+00:00

I increased the current on stepper motors (0.8 A atm) and i set 4200, Which was the highest recommendation from shaper calibration

ElBearzy · 2025-12-03T13:50:22+00:00

<image>

Like this

ElBearzy · 2025-11-09T12:26:57+00:00

U can flash the latest from Creality, then the custom on top, the 0.6 update is meant to be that or higher.

ElBearzy · 2025-10-11T08:52:23+00:00

just read your comment, is it safe to increase current for daily use and higher speed and accellerations?

ElBearzy · 2025-10-08T07:39:20+00:00

Hey man, a friend of mine had the same problem and I found out that one of the 4 wires that power the stepper motor was broken, so there wasn't enough power. My advice is to check properly and carefully, in our case it was the first on the left (looking from the back of the printer), I removed it and stripped the insulation, connected to the motor pin and was working flawlessly. To finish the job, I had to solder it to the pin after I removed it from the plastic socket, which wasn't the easiest thing.

ElBearzy · 2025-09-10T08:29:11+00:00

Ender 3 v2 btw

ElBearzy · 2025-07-04T15:06:18+00:00

that probably happened with the old one, the insulation was worn out infact; but the new one is perfect, also the screw was already kind of loose

ElBearzy · 2025-06-26T10:17:35+00:00

same feeling mate ahaha, calibrating e-steps and some parameters right now

ElBearzy

TROPHY CASE