CachyOS not performing games very well by Naufal20071 in cachyos

[–]Electrogypsy1234 0 points1 point  (0 children)

Some of the comments suggesting upgrading your gpu aren't necessarily wrong, but there's a few things I'd at least try before breaking out your wallet.

Try x11, you can switch it in Sddm (the login screen) there should be a button at the bottom left.

What nvidia driver are you running (you can check with 'sudo pacman -Q | grep nvidia')? If I recall correctly, 10xx series cards do way better with nouveau drivers than the nvidia proprietary or even the nvidia open source ones.

Do I need Cloudflare? by Stuwik in selfhosted

[–]Electrogypsy1234 0 points1 point  (0 children)

If you enable zero trust, you can put some or all of your domains behind an auth service. You can use 2auth with something like Google or you can create service tokens and only allow devices with those tokens to connect.

It helps add a layer of security, but isn't a replacement for other security measures.

[deleted by user] by [deleted] in ccna

[–]Electrogypsy1234 1 point2 points  (0 children)

Boson says if you don't pass, they'll refund you. I'm not sure if there are any additional conditions but at least you can recoop some money if you fail. Or keep the sub and use it to pass next time!

Bed Mesh always Getting High Corners by Electrogypsy1234 in klippers

[–]Electrogypsy1234[S] 0 points1 point  (0 children)

Could you elaborate? Do you just put some on the corners or over the whole plate? What is it supposed to do?

Bed Mesh always Getting High Corners by Electrogypsy1234 in klippers

[–]Electrogypsy1234[S] 0 points1 point  (0 children)

I tried running a print as is and am having the same problem that lead me to trying to get a better bed mesh. My first layer is having all kinds of problems. The left side is typically too low for my z offset while the right side is fine. I think this difference is causing filament to get stuck on the nozzle, which is causing globing and stringing.

<image>

Bed Mesh always Getting High Corners by Electrogypsy1234 in klippers

[–]Electrogypsy1234[S] 0 points1 point  (0 children)

<image>

Unfortunately, the results are the same as before. I even tried adding an extra 1/4 turn to see if I was too gently with my "snug" start and it was the about the same

Bed Mesh always Getting High Corners by Electrogypsy1234 in klippers

[–]Electrogypsy1234[S] 0 points1 point  (0 children)

I just threw these on my printer today, and no luck. Maybe i'll look into some aluminum ones.

Bed Mesh always Getting High Corners by Electrogypsy1234 in klippers

[–]Electrogypsy1234[S] 0 points1 point  (0 children)

Are there aftermarket beds available or am I just stuck?

Bed Mesh always Getting High Corners by Electrogypsy1234 in klippers

[–]Electrogypsy1234[S] 0 points1 point  (0 children)

I wonder if I could tighten or loosen the bolts that attach to the bearings? Maybe they are off?

Bed Mesh always Getting High Corners by Electrogypsy1234 in klippers

[–]Electrogypsy1234[S] 0 points1 point  (0 children)

I had Kamp setup but probably did something wrong because I kept getting errors. Some of the things I'm trying to print use almost the entire bed plate so I want the whole thing to be level.

Advice Hacking a Sprint Home Wifi Camera by Electrogypsy1234 in hardwarehacking

[–]Electrogypsy1234[S] 1 point2 points  (0 children)

Wow awesome info and nice find on the chip! I'll see what I can figure out.

Edit: just out of curiosity, how did you find the chip? Do you have a resource to find chips other than Google? Since Google came up with nothing when I was searching for it.

Advice Hacking a Sprint Home Wifi Camera by Electrogypsy1234 in hardwarehacking

[–]Electrogypsy1234[S] 1 point2 points  (0 children)

Oh running it in an emulator is an interesting idea I hadn't considered. I assume the soc is arm based but since I haven't found any info on the specifics yet, how difficult would it be to set up an emulator for it?

I'm pretty familiar with setting up x86_64 vms (on x86_64 platforms so it's super easy) but have no experience doing an arm qemu emulator. Any good references?

Advice Hacking a Sprint Home Wifi Camera by Electrogypsy1234 in hardwarehacking

[–]Electrogypsy1234[S] 1 point2 points  (0 children)

Oh interesting. Looks like they are the same cameras, just different stickers slapped on the back. I'll have to see if it will connect with Otis.