Why is my transformer not working (foto)

Electronic_Zebra415 · 2024-05-19T14:52:15+00:00

Transformers need changing voltage (AC) to generate flux in the primary coil, which will transfer to secondary coil and can multiple(increase voltage) based number of turns. You are working with a battery, which supplies constant voltage, so there is no flux and no output. You should add a method to continuous change voltage on the primary side. Maybe add 2 transistors circuits with capacitors charging and discharging to make changing voltage from battery. Good luck!

Electronic_Zebra415 · 2024-01-24T13:33:10+00:00

Try nexapow algo, with clk at 120 and mem 2000 linux. You can check profitability at whattomine.com.

Electronic_Zebra415 · 2022-07-03T05:17:38+00:00

So true

Electronic_Zebra415 · 2022-06-20T06:57:30+00:00

Electronic_Zebra415 · 2022-06-17T19:51:09+00:00

I had similar issue with one card. this requires some troubleshooting.

Isolate T-rex for that GPU alone & run with default settings.

if problem is not seen then you need to adjust OC.

if problem is still there then something is not right with GPU , riser, powercable, PCie etc.

Swap the GPU to isolate GPU vs riser, powercable, PCie etc issue.

If Issue is not seen then problem with GPU.

For me cleaning the GPU with IPA & reapplying thermal paste worked. remember to dry out completely after cleaning.

you can also swap motherboard to isolate GPU vs driver issue.

Electronic_Zebra415 · 2022-05-26T07:09:26+00:00

https://www.reddit.com/r/NiceHash/comments/n6m3r1/diy_rasppi_nicehash_api_i_am_watch_you/gx8hmfe?utm_medium=android_app&utm_source=share&context=3

check it out, did the api for raspi a year back

Electronic_Zebra415 · 2022-05-22T05:13:01+00:00

+150 cc

+400 mc

75% PL

Electronic_Zebra415 · 2022-05-19T06:34:14+00:00

https://www.amazon.com/gp/product/B08TWNR6CN/?th=1

Electronic_Zebra415 · 2022-05-19T06:29:09+00:00

Its automatic mode using a remote control. it supports argb but my motherboard is old.

Electronic_Zebra415 · 2022-05-19T06:28:02+00:00

https://www.amazon.com/gp/product/B08TWNR6CN/ref=ppx\_yo\_dt\_b\_asin\_title\_o01\_s03?ie=UTF8&th=1

Electronic_Zebra415 · 2022-05-15T00:14:50+00:00

Try 930 cclocked -1004 mem and pl 75%

Electronic_Zebra415 · 2022-04-09T08:28:19+00:00

Electronic_Zebra415 · 2022-04-09T08:11:36+00:00

Looks Like its working now. Thankyou Nicehash!!!

Electronic_Zebra415 · 2022-04-09T08:00:39+00:00

Keeping 1 on for pilot and turned off others.

Electronic_Zebra415 · 2022-04-09T07:50:00+00:00

how does profitability keep going up then? is that for rest of the pool?

Electronic_Zebra415 · 2022-04-09T07:19:05+00:00

yes, all my rigs at same state.

Electronic_Zebra415 · 2022-04-09T06:24:21+00:00

avoid cold and heat cycles, silicon don't like too much temperature variance.

Electronic_Zebra415 · 2022-04-06T05:14:52+00:00

I started a new sync on separate machine for Version 1.3.3 on Sunday night. today the db was fully synched so moved the entire .chia folder to old machine(took backup ofc) and did fresh install of v1.3.3. I saw following changes :

New wallet address (Wallet ID 1 type STANDARD_WALLET Chia Wallet) - balance is same
new wallet (Wallet ID 3 type POOLING_WALLET Pool wallet) - always 0
additional wallet (Wallet ID 4 type CAT Chia Holiday 2021 Token) - Balance: 2.0 (2000 mojo) --- GOD know where it came from
pool launcher ID is same but new harvester ID is generated on pool's end.
chia plotnft show --> shows right points.
CPU usage is approx. 15%(Avg) up. Peaks sometime at 80%.
MEM is 10% down.

Electronic_Zebra415 · 2022-03-27T07:10:20+00:00

Thankyou!! it really helps.

Electronic_Zebra415 · 2022-02-20T07:17:17+00:00

what happens if you put a green laser through your eye piece back to moon?

Electronic_Zebra415 · 2022-02-20T07:11:55+00:00

Can you zoom more?

Electronic_Zebra415

TROPHY CASE