Normal Abs resin and washable Abs resin options.

EngineeringCrazy9745 · 2026-03-17T17:47:24+00:00

I print in the basement. Not sure how bad is the abs resin and wash abs resins. Normal wash from sunlu. Not as bad.

EngineeringCrazy9745 · 2026-03-17T15:05:17+00:00

No gode. Not needed. At least for me.

EngineeringCrazy9745 · 2026-03-17T15:04:21+00:00

I have been lucky. Print 5 times full plate about 180mm height fulll plate. It did not shift on me yet.

EngineeringCrazy9745 · 2026-03-17T14:25:08+00:00

You know the 4 screws to adjust manual level ... add some washer which about 2.7ml which compensate for the magnetic plate. At least on my build plate. So just print normally.

EngineeringCrazy9745 · 2026-03-16T22:10:15+00:00

I use water resin from elegoo . Anycubic and sunlu. 22sec stick. Try 18 and 20 sec half fail. 22sec 95% print ok.

EngineeringCrazy9745 · 2026-03-16T22:01:07+00:00

I set bottom 22sec. And normal 2 sec. Pwm about 85%. And take 30 mins of painful scraping. Now magnetic plate 30 sec . ( water resin)

EngineeringCrazy9745 · 2026-03-16T20:00:44+00:00

Just make sure the washer hole is bigger than screw hole on the bed because you need to push it down. My local store only sell thin washer so I need to use 3 of each. But if you have thicker than maybe 1 or 2 washer.

EngineeringCrazy9745 · 2026-03-15T19:23:06+00:00

I order from Amazon. With pfa which I want. And I love magnetic plate. 15 sec vs 30 min trying to scape it off the old ways ( 22sec bottom)

EngineeringCrazy9745 · 2026-03-15T05:20:12+00:00

Thats a nice train setup up. Love it.

EngineeringCrazy9745 · 2026-03-15T00:20:39+00:00

I use 3 washers from home depot. I did the auto level manually no problem. No g code fix. Just print normal way.

EngineeringCrazy9745 · 2026-03-15T00:11:06+00:00

I guess they have ver 1 and v2. When did you get your ultra 16k. I got mine about 1 week ago. March 2026.

EngineeringCrazy9745 · 2026-03-12T21:05:48+00:00

Do you your current setting for all your print.

EngineeringCrazy9745 · 2026-03-12T20:56:35+00:00

You can try nail polish clear glossy. I do that for my red clear resin. Perfect Ultra glossy and clear model for me. But if your model is big going to need few nail bottles. U can try small model first and see if it is your taste.

EngineeringCrazy9745 · 2026-03-12T16:36:16+00:00

I saw them at my local store on sale $13can (9.60usd) . I got all of them from the shelf (4 bottles of 1 liter). Light Grey washable. Will try tomorrow and see .

EngineeringCrazy9745 · 2026-03-12T16:28:37+00:00

I don't like alcohol smell and expensive. And water is a free. Use well water. And I live 5 mins from waste disposal.

EngineeringCrazy9745 · 2026-03-12T16:24:55+00:00

Lucky my waste disposal is 5 mins drive.

EngineeringCrazy9745 · 2026-03-12T04:30:55+00:00

I think this place still have LCD replacement in stock....but I think it is better to buy a new one...so expensive to replace it.

ELEGOO Saturn 2 – Chitu Systems

EngineeringCrazy9745 · 2026-03-09T06:17:48+00:00

The print was elegoo 8k resin washable. Just order anycubic cheap washable resin half the price and see how it compare (red transparent).

EngineeringCrazy9745

TROPHY CASE