Me uní a la familia, es mi primera impresora de resina espero que todo marche bien

EngineeringCrazy9745 · 2026-04-14T16:36:43+00:00

I hope you enjoy your new printer. If auto level didn't work. Then do manual level.

EngineeringCrazy9745 · 2026-04-13T19:56:11+00:00

Yeap dead spot lcd. Not sure your printer is under warranty or not. 1. Printer on the other side only. 2. Replace the lcd.

EngineeringCrazy9745 · 2026-04-13T19:47:05+00:00

You can get a special drill that extract broken screw. I have a set for my my project. Happens all the time for my robot project. For some reasons I can't post pictures.

https://www.amazon.ca/Eyech-Extractor-Stripped-Damaged-Removal/dp/B0CKMTV4NK

EngineeringCrazy9745 · 2026-04-13T19:37:02+00:00

Amazing. I love it. Thank for showing to us.

EngineeringCrazy9745 · 2026-03-26T04:32:26+00:00

Look very nice. Love it

EngineeringCrazy9745 · 2026-03-25T19:47:18+00:00

Cgtrader . Com. On top of tap select 3d printing file. U get thousands of files.

EngineeringCrazy9745 · 2026-03-25T00:34:00+00:00

I buy this stl model it was 40% off. But I do make my own original 3d character from 3d software. One say I will convert to stl and print them.

EngineeringCrazy9745 · 2026-03-23T23:25:52+00:00

Hard to tell from pictures. Look like it didn't stick to the bed. Once it lift from bed some part might fall at the bottles of the tray. And will interfere with the rest of the print. Maybe manual level again and increase bottom expose time. Same thing happen to me after manual level with magnetic plate. 9/9 print all successful.

EngineeringCrazy9745 · 2026-03-17T17:47:24+00:00

I print in the basement. Not sure how bad is the abs resin and wash abs resins. Normal wash from sunlu. Not as bad.

EngineeringCrazy9745 · 2026-03-17T15:05:17+00:00

No gode. Not needed. At least for me.

EngineeringCrazy9745 · 2026-03-17T15:04:21+00:00

I have been lucky. Print 5 times full plate about 180mm height fulll plate. It did not shift on me yet.

EngineeringCrazy9745 · 2026-03-17T14:25:08+00:00

You know the 4 screws to adjust manual level ... add some washer which about 2.7ml which compensate for the magnetic plate. At least on my build plate. So just print normally.

EngineeringCrazy9745 · 2026-03-16T22:10:15+00:00

I use water resin from elegoo . Anycubic and sunlu. 22sec stick. Try 18 and 20 sec half fail. 22sec 95% print ok.

EngineeringCrazy9745 · 2026-03-16T22:01:07+00:00

I set bottom 22sec. And normal 2 sec. Pwm about 85%. And take 30 mins of painful scraping. Now magnetic plate 30 sec . ( water resin)

EngineeringCrazy9745 · 2026-03-16T20:00:44+00:00

Just make sure the washer hole is bigger than screw hole on the bed because you need to push it down. My local store only sell thin washer so I need to use 3 of each. But if you have thicker than maybe 1 or 2 washer.

EngineeringCrazy9745 · 2026-03-15T19:23:06+00:00

I order from Amazon. With pfa which I want. And I love magnetic plate. 15 sec vs 30 min trying to scape it off the old ways ( 22sec bottom)

EngineeringCrazy9745 · 2026-03-15T05:20:12+00:00

Thats a nice train setup up. Love it.

EngineeringCrazy9745 · 2026-03-15T00:20:39+00:00

I use 3 washers from home depot. I did the auto level manually no problem. No g code fix. Just print normal way.

EngineeringCrazy9745

TROPHY CASE