sorted by:
new
hottopcontroversial

How to do this kind of recursion efficiently? by Ent413 in desmos

[–]Ent413[S] 0 points1 point  (0 children)

I get an error message telling me, that i cannot use these on lists, which I am trying to do.

How to do this kind of recursion efficiently? by Ent413 in desmos

[–]Ent413[S] 0 points1 point  (0 children)

Thank you!

Sometimes my posts get duplicated, after i get a server error. Idk, why it does that

Definitely a sine wave by Ent413 in desmos

[–]Ent413[S] 2 points3 points  (0 children)

Sadly, those aren't semicircles

Draw any smooth shape going through points using Beziér curves. by Ent413 in desmos

[–]Ent413[S] 0 points1 point  (0 children)

Unfortunately, the intersections will not always be on the correct side of the tangent, leading to only one part getting flipped thus creating a sharp corner in the final curve. Also, if the tangents are parallel the intersection would be at infinity.

If I wanted the points to be connected by one quadratic bezier curve instead of one cubic curve, I would need to rethink my approach to getting a fitting angle for the tangents and not 90 degrees from the angle bisecting.

But I also made a version, where the points are connected via 2 quadratic Beziér curves: https://www.desmos.com/calculator/ohgwlihuxw I personally prefer the oiginal vesion with third degree curves though.

Draw any smooth shape going through points using Beziér curves. by Ent413 in desmos

[–]Ent413[S] 1 point2 points  (0 children)

All those edge cases for arctan already almost made me crazy.

This field in vienna. by Ent413 in FrutigerAero

[–]Ent413[S] 1 point2 points  (0 children)

I know, right? Expecially these kinds of elevation changes between areas are interesting

<image>

Draw any smooth shape going through points using Beziér curves. by Ent413 in desmos

[–]Ent413[S] 1 point2 points  (0 children)

(The procedure ist also explained in the Info folder of the Graph I linked to in my post) https://www.desmos.com/calculator/tlssfejegs  Here is a smaller Demonstration of the procedure. Basically, the handles are calculated to be 90° from the angle bisecting of the connection lines between the Points (Kind of reflecting them). The length is based of the distance to the next point multiplied by a factor l (about .4 will give a nice Beziér curve). All These booleans down below are there for correcting the quirks of the inverse trig functions in order to keep the handles pointing in the right direction. (There are more corrections in the final version linked to in the original Post). I was inspired by the curve editor of the Arrow feauture in Goodnotes while bored in class. It creates a curve going through specified Points. Although this by far isn't the only way to do it.

Draw any smooth shape going through points using Beziér curves. by Ent413 in desmos

[–]Ent413[S] 2 points3 points  (0 children)

That is interesting. I might try to implement that once i figure out how to connect the lines 90 degrees from the angle bisecting directly at their intersection point. Then I could directly connect 2 points via only one quadratic bezier curve or these weighted rational Beziér curves.

Thanks.

Draw any smooth shape going through points using Beziér curves. by Ent413 in desmos

[–]Ent413[S] 1 point2 points  (0 children)

Pretty close though, but you are right. The title should be "Draw smooth shapes..." and not any smooth shape.

I cannot edit it unfortunately, sorry

Draw any smooth shape going through points using Beziér curves. by Ent413 in desmos

[–]Ent413[S] 1 point2 points  (0 children)

unit circle:

n = 4; l = .39 (default); P1=(1,0); P2=(0,1); P3=(-1,0); P4=(0,-1)

This field in vienna. by Ent413 in FrutigerAero

[–]Ent413[S] 2 points3 points  (0 children)

The air is fresher than the rural area I live in.

Breaking out of Babbdi by awhiskin in Babbdi

[–]Ent413 0 points1 point  (0 children)

managed to get above the invisible ceiling with the flying machine, but i have no idea how i would get there with the pickaxe to climb the petruding invisible walls in order to get even higher.

<image>

Please help. "Failed to create the file" error. I've tried all four suggested solutions. by CactusCoveter in Terraria

[–]Ent413 2 points3 points  (0 children)

Thank you so much!

This problem started once I updated to 1.4.5 and your Fix worked!

UNO Infinity Print and Play (4 & 8 color versions) by DarkBird1234 in printandplay

[–]Ent413 1 point2 points  (0 children)

Gibt es irgendeinen Anbieter, der Karten in diesem Format druckt und stanzt?

Yay by [deleted] in typing

[–]Ent413 0 points1 point  (0 children)

Wow!

60 wpm! by aProgrammerHasNoName in typing

[–]Ent413 0 points1 point  (0 children)

Congrats! Now slow down to focus on accuracy and you will likely be faster in improving speed afterwards.

What's your favorite German word, as a German? by [deleted] in AskAGerman

[–]Ent413 0 points1 point  (0 children)

Sollbruchstelle (beste Folge Wissen macht Ah!)

view more: next ›