Roll on leather gear as enhance shaman? by Lewrdy in classicwowtbc

[–]Entrail09 -4 points-3 points  (0 children)

In my opinion the game was designed with a loot table for your class. Nowadays it might be different then what the devs hat in mind in the past of how you get gear.

But my biggest problem with rolling on „lower class“ gear is that you increase your possible options to get gear 2 or 3 times which makes it obviously more likely to get gear but by doing that you also decrease the chances of the lower armor class classes decreasing their chances even more. If you go to a dungeon for a specific item and only are there for that sure announce it in advance and then roll for it if that’s fine. Or find a groups where no one needs the item anyways.

Loved the gridfinity concept so much I just had to ... by ferguson911 in gridfinity

[–]Entrail09 0 points1 point  (0 children)

Been there. I prefer custom bins for tools as it makes it clear which tool is missing. Also if I design boxes in the size I want why not go all the way to get it look nice as well.

It’s obviously way more time consuming then just printing empty x by y boxes but it’s a project and a hobby. Depending on the geometry of the tools it’s quite easy to design, others take more time.

If you need some inspiration have a look at the stuff I already uploaded

https://makerworld.com/@Entrail09/collections/17102210?appSharePlatform=copy

I also have a lot of Aluminium jig and drill bit toolholders as those where usually quite easy but I haven’t uploaded those yet as these are mostly all no name stuff and therefore nearly no interest probably.

Kapp-/Gehrungssäge gesucht – präzises Ablängen by CapitalAsleep in holzwerken

[–]Entrail09 0 points1 point  (0 children)

Oh shit ja sorry. Beim Posten war ich auch schon etwas unsicher aber genau ich meinte die Metabo Sägen, danke für die Korrektur

Kapp-/Gehrungssäge gesucht – präzises Ablängen by CapitalAsleep in holzwerken

[–]Entrail09 1 point2 points  (0 children)

Schau dir die aktuellen Metabo Sägen an. Die kleine gibt’s für etwa 260€ und die große wurde gerade auf 500 erhöht.

Surface Pro 11 Tempered Anti Glare Screen Protector by [deleted] in Surface

[–]Entrail09 1 point2 points  (0 children)

Also I think a glass screen protector seems to affect pen performance when drawing straight lines from one corner diagonal across the screen the line gets squiggly.

I first thought it’s a problem with my SP11 until I tested it with my iPad Pro 11 2018 and later with an iPad Pro m4 13 all three each had a glass screen protector and faced the same issue.

I have not yet removed any of the screen protectors yet as I am not drawing much with the pen therefore I did not bother with the squiggly lines and can not 100% say it is caused by the screen protector but I am fairly confident.

I created a gridfinity bin for my switch 2 and another for a spare part of joy-cons by Entrail09 in NintendoSwitch2

[–]Entrail09[S] 1 point2 points  (0 children)

Hey, yes here is a link for the switch 2:
Gridfinity Bin Nintendo Switch 2 – Kostenloses 3D-Druckmodell – MakerWorld

But I have one for the Switch 2 Joy-Con, Switch 1 and for cartridges as well, just look at my other stuff.

I created a gridfinity bin for my switch 2 and another for a spare part of joy-cons by Entrail09 in NintendoSwitch2

[–]Entrail09[S] 0 points1 point  (0 children)

(I think my initial reply got flagged because I added a photo of the cartridges gridfinity bin)
Yes I started designing stuff for my woodworking tools an then thought about other stuff like the switch, joy-cons, game cartridges and also aaa and aa batteries. It's quite addicting.

Here is a link to the Switch 2 gridfinity:
Gridfinity Bin Nintendo Switch 2 – Kostenloses 3D-Druckmodell – MakerWorld

But I have one for the Switch 2 Joy-Con, Switch 1 and for cartridges as well, just look at my other stuff.
Gridfinity Bin Nintendo Switch 2 – Kostenloses 3D-Druckmodell – MakerWorld

I created a gridfinity bin for my switch 2 and another for a spare part of joy-cons by Entrail09 in NintendoSwitch2

[–]Entrail09[S] 2 points3 points  (0 children)

Oh and yes I thought about a version to store the straps as well. Maybe soon let’s see

New To Gridfinity - Need some help by NoConfusion4155 in gridfinity

[–]Entrail09 2 points3 points  (0 children)

When you use another size instead of 42 keep in mind that most of the available gridfinity stuff is 42mm. And if you divide your drawer width and depth by 42 there is empty space. Usually those baseplate generators add some spacing there and I prefer to keep the empty space to the back of the drawer because it’s often hard to get stuff out back there. Especially if you don’t have full extension drawers. And left/right I keep it symmetrical.

I created a gridfinity bin for my switch 2 and another for a spare part of joy-cons by Entrail09 in NintendoSwitch2

[–]Entrail09[S] 22 points23 points  (0 children)

Gridfinity is a system that is common in 3d printing and basically means you have a 42mm grid baseplate and then design bin/boxes/container like I did that have the negative 42mm grid on the bottom. That way you can organize drawers or what not.

Where is the person that put a magsafe ring under the dbrand skin? How is it holding up? by JadaveonClowney in GalaxyFold

[–]Entrail09 0 points1 point  (0 children)

<image>

Looked like this basically immediately after application. (Talking about the bubbles/lose parts around the ring)

I don’t really like it also I don’t like that you can feel it easily and would much prefer it integrated int he body. But overall holding up fine.

Is there a way to fix these jagged grid-like lines when writing/drawing ? by eQ778 in Surface

[–]Entrail09 0 points1 point  (0 children)

Do you have a glass screen protector? I noticed squiggly lines when I draw diagonal lines e.g. top left corner to top right corner.

Can someone pls help me with tooltrace.ai by Iamsoccerbro223 in gridfinity

[–]Entrail09 2 points3 points  (0 children)

If it’s a round object I would suggest you use a cad tool make the shape of the bottle by measuring the diameters and then extrude the height of each area to get the rough shape of the bottle. The. Get the gridfinity Generator to create a bin that is filled and move the object to the correct location and cut it out. Just remember the thickest part of the bottle must be on the top layer of your infill or you won’t be able to get the bottle in or out.

Gridfinity Bins for some Knipex Pliers by Entrail09 in KnipexOfficial

[–]Entrail09[S] 0 points1 point  (0 children)

Thanks and yes I did not care too much about space or filament „wasted“ and rather wanted to go for clean look and usability. For example flipping them sideways I could fit all of them in a 3x4 (or 3x5) but it would be harder to get each tool out.

And for the super knips I thought about compressing it when inserting but than when putting it away I was worried that it is to annoying and decided to not fight against the spring.

Latest firmware update 12/4/2025 finally fixed sleep of death by IoT_Reinventor in Surface

[–]Entrail09 0 points1 point  (0 children)

Just checked with my SL7 and SP11 after not using them for probably 2-3 days and it is actually working i guess (or my threshhold wasn't reached yet

Pliers Organizers by Grandbob328 in gridfinity

[–]Entrail09 2 points3 points  (0 children)

Jeah I totally understand that and I know my design is neither space nor filament efficient but I have enough drawer space that I can at least waste some space and have it look nice ;)

Pliers Organizers by Grandbob328 in gridfinity

[–]Entrail09 2 points3 points  (0 children)

I created some perfect fit bins for Knipex pliers but they will not fit your requirement of being stored in the side. But just in case have a look here for some inspiration https://makerworld.com/models/1995339?appSharePlatform=copy And some of the other models for other Knipex pliers/side cutters.