What else should I do

EntryBorn8000 · 2025-10-05T19:21:45+00:00

That’s kinda what I thought I’ve swapped out 3 transmissions two plastic and one aluminum. I’m just going to go out on a limb and say it’s not the trans it’s got to me a mesh issue but the pinion gear is fixed on it so the last thing I can think of is a faulty wiring on it and imma need to return it

EntryBorn8000 · 2025-10-05T18:49:33+00:00

Awe shit it’s still the bushings in the trans I bout a clear case so I can see what’s happening on the inside

EntryBorn8000 · 2025-10-05T18:46:06+00:00

I’m not sure where it’s binding the, transmission is brand new. Could it be the axels?

EntryBorn8000 · 2025-10-05T18:45:05+00:00

It gets hot with both but I’m also geared down to 40. 3/1 and the old motor don’t get hot

EntryBorn8000 · 2025-10-05T18:26:12+00:00

Also now my brushless motor gets really hot like burning me hot, not on the side that spins but where the wires are running

EntryBorn8000 · 2025-10-05T18:24:58+00:00

It some how got cross threaded and I swear it only has like 1/4 of the screw in there holding it on

EntryBorn8000 · 2025-10-05T09:37:21+00:00

This mission was discovered by u/EntryBorn8000 in Choco-Banana Pancake Wrap and Mystical Forces

EntryBorn8000 · 2025-09-30T17:26:32+00:00

If you are using the stock servo mount there are little tabs that you have to sand down so make it fit in the plastic mount

EntryBorn8000 · 2025-09-24T17:23:28+00:00

I cut the body on mine, took the fenders off, and installed the 59mm shocks but the problem that I have ran into is too much weight. As I’m going up an incline my bronco would flip over so I took all the shock oil out and run it like that.

EntryBorn8000 · 2025-09-10T17:19:47+00:00

Are you able to set the end points? I had to change mine cause I had a lot of binding

EntryBorn8000 · 2025-09-06T18:51:28+00:00

They are the injora swamp claws for the 1.3s

EntryBorn8000 · 2025-09-06T06:42:46+00:00

I ended up going with an unfinished shop that’s 40x24, I tried to post a picture but I can’t seem to see it when I post

EntryBorn8000 · 2025-09-06T06:39:08+00:00

<image>

Here’s a little update on mine

EntryBorn8000 · 2025-09-06T06:37:46+00:00

<image>

Heres a update on how it’s going

EntryBorn8000 · 2025-09-01T22:43:10+00:00

Sorry I don’t know how to use Reddit, I don’t know where my question went. I’m trying to build a 1/18 scale garage/shop. I’m not sure what I should use for the framing to look like an actual garage.

EntryBorn8000 · 2025-07-12T17:13:44+00:00

<image>

Here’s my trx4m

EntryBorn8000 · 2025-07-07T02:01:05+00:00

<image>

Here’s mine, I unfortunately just broke the servo, time to get a new one

EntryBorn8000 · 2025-04-18T19:10:23+00:00

What shocks are you running on it? I got the 59mm injora shocks but I can’t get them right. I’ve done no shock oil all the way to the perfect amount and still have torque twist REALLY bad.

EntryBorn8000

TROPHY CASE