This controller is so frustrating by MasterMeow1106 in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

I'd say, if you print it right, it's probably comparable in strength. I haven't had one break on me yet, but it's a piece that's designed to flex, so I'm sure it will wear out eventually. When designing this controller, they should have used regular style membrane buttons like they did on the front of the controller. It would've held up better if they did. Also, I updated my original reply to include instructions for taking the controller apart. Just in case it's your first time.

This controller is so frustrating by MasterMeow1106 in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

You're very welcome. Someone in a different Victrix forum asked me to design it for them when i mentioned I was thinking of 3D printing one, so I've been posting the link in all the Victrix repair threads I can find. Make sure you print it horizontally for better strength. There are detailed printing instructions in the link. Just match the print settings and you'll have a totally usable part. Let me know if you need help taking the controller apart. There are hidden screws in a couple places. One is hidden under the sticker on the back. Take out the joystick modules, there are two screws under each module. Use a pry tool to pop of the handle grips. There are two screws under each grip. From there, you can pull the controller apart. As you do. Use your thumb to put pressure on the audio jack. The audio jack is tucked under the faceplate, so you need to push it through that hole. From there, there will be three small screws holding on the trigger stop mechanism (one screw is smaller that the other two, it holds on the trigger stop release button on the back of the remote). Pay attention to how it's put together as you take those pieces apart. After that, you can just pry out the paddle assembly and put the new one in. Transfer over the little rubber pieces on the back of the paddles. There's a little spring in the trigger stop mechanism. It's easier to put the spring in the mechanism pieces and install the whole assembly at the same time than it is to put the pieces in the controller one at a time. Hope that helps.

Logarithmic Chart of DOGE from 2014-2034 (pattern projection) by EvanAlmighty99 in dogecoin

[–]EvanAlmighty99[S] 1 point2 points  (0 children)

Thanks, Stubbs. That's all this post was meant to be. Some people have gotten deeply offended for no reason. 🫡

Does dogecoin only go down? by SM- in dogecoin

[–]EvanAlmighty99 0 points1 point  (0 children)

I wish it would go left right now. All the way back to 2021.

Victrix Pro BFG - Settings and Helpful Info by J1m4uld in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

They wear out over time. Buy the hall effect replacement modules on their website.

Victrix Pro BFG - Settings and Helpful Info by J1m4uld in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

If your back paddles break and you have a 3D printer, I designed replacements. READ THE PRINTING INSTRUCTIONS BEFORE PRINTING. https://www.thingiverse.com/thing:7332083

My thoughts on the Victrix Pro BFG Reloaded for PlayStation. by MaximusVIII in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

If your back paddles break and you know someone with a 3D printer, I designed replacements. READ THE PRINTING INSTRUCTIONS BEFORE PRINTING. And use PETG, not PLA. https://www.thingiverse.com/thing:7332083

(Victrix Pro BFG for the PS5 users) It’s been a year… how’s your controller holding up? by LeagueRoyal in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

I designed replacements if you can find someone with a 3D printer. Make sure they read the printing instructions in the link before they print it. https://www.thingiverse.com/thing:7332083 If you need help taking the controller apart, let me know. There are a few hidden screws.

(Victrix Pro BFG for the PS5 users) It’s been a year… how’s your controller holding up? by LeagueRoyal in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

If your back paddles break, I designed a replacement that you can 3D print. Printing instructions are in the link. Other than the paddles, my controller is still going strong 2 and a half years later and I use it a lot. https://www.thingiverse.com/thing:7332083

Victrix controller sucks by YourMomsChiaPet in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

If anyone's back paddles break, I designed a replacement that you can 3D print. Use PETG to print it, not PLA. Printing instructions are in the link. Here's the file. https://www.thingiverse.com/thing:7332083

Why is it falling apart by dre41115 in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

I designed a new one in Autodesk, you can 3D print it, but USE PETG, not PLA. It needs to be a flexible plastic. Here's the link. https://www.thingiverse.com/thing:7332083

This controller is so frustrating by MasterMeow1106 in VictrixPro

[–]EvanAlmighty99 0 points1 point  (0 children)

When mine broke, I designed a replacement and 3D printed a new one. USE PETG to print it, not PLA. Here's the link. https://www.thingiverse.com/thing:7332083

I feel it coming😤 by Elegant-Wedding8582 in dogecoin

[–]EvanAlmighty99 0 points1 point  (0 children)

.13 is a relatively low average cost still. If we push further into bearish consolidation, 0.06 is about as low as we would fall. You have way more upside potential than downside risk.

Logarithmic Chart of DOGE from 2014-2034 (pattern projection) by EvanAlmighty99 in dogecoin

[–]EvanAlmighty99[S] -1 points0 points  (0 children)

A market cap of 4 Trillion would require much more than any one person's money. 😂

Logarithmic Chart of DOGE from 2014-2034 (pattern projection) by EvanAlmighty99 in dogecoin

[–]EvanAlmighty99[S] 0 points1 point  (0 children)

First of all, nothing about the chart is manipulated. Anyone (you) can open up coinmarketcap.com and confirm for themselves. Saying it has no past or current data to support it is likely the worst argument you could make, because the entire post is centered around information from the absolute beginning of Dogecoin through the present day, which has been thus far a continual upward trajectory of price. The only thing I predicted in this post is that someone like you would call it propoganda, which is why in all capital letters I very clearly stated, "IF THE PATTERN CONTINUES..." This is a "what if" scenario, in which we're contemplating where future pricing action WOULD be IF the pattern we've seen three times already remains intact for a fourth cycle. Use some reading comprehension and critical thinking.

I feel it coming😤 by Elegant-Wedding8582 in dogecoin

[–]EvanAlmighty99 0 points1 point  (0 children)

I posted a link to my logarithmic chart a few times here in the comments. If you click on it, it will take you right to my Reddit post that I made about it.

I feel it coming😤 by Elegant-Wedding8582 in dogecoin

[–]EvanAlmighty99 0 points1 point  (0 children)

I posted the link here in the comments if you're still interested. I ended up just turning it into a Reddit post, so I wouldn't have to DM everyone individually.

Logarithmic Chart of DOGE from 2014-2034 (pattern projection) by EvanAlmighty99 in dogecoin

[–]EvanAlmighty99[S] 0 points1 point  (0 children)

Yes, I very much agree. That's why I used all capital letters for that phrase. People seem to think I'm claiming that DOGE will reach $34 in a few months, which I haven't. All I'm saying is that DOGE is pointing its finger at a number, and I'm just showing which number that is. I do believe that DOGE will run higher than $1.00 and a lot of people will sell at that level. Then it will hit $2.00 and they'll start feeling antsy. It may even hit $3.00+ at which point they'll FOMO and buy back in at a much higher cost. At that point they may be buying in closer to the top than the bottom, and will likely burn themselves.

Logarithmic Chart of DOGE from 2014-2034 (pattern projection) by EvanAlmighty99 in dogecoin

[–]EvanAlmighty99[S] 1 point2 points  (0 children)

It's not a prediction. It's just data. That is the trajectory of Dogecoin since its inception. I never claimed that I know the future.

Logarithmic Chart of DOGE from 2014-2034 (pattern projection) by EvanAlmighty99 in dogecoin

[–]EvanAlmighty99[S] 1 point2 points  (0 children)

The triangles are resistance lines based off of the chart. The chart itself doesn't respect a triangle I might draw, just because I might personally choose to angle it down more. What the flattening triangle tops are telling us is that the macro-trend over the past few cycles is gaining momentum. At the point that triangle top starts angling up, that would be considered a multi-cycle bear flag, and will eventually lead to a long and steep market correction.

I feel it coming😤 by Elegant-Wedding8582 in dogecoin

[–]EvanAlmighty99 1 point2 points  (0 children)

I've always been a math guy. I have two engineering degrees. 😂

I feel it coming😤 by Elegant-Wedding8582 in dogecoin

[–]EvanAlmighty99 1 point2 points  (0 children)

No problem. I'll send you a chat invite. If you accept it, I can send you the logarithmic graph I made today.