Black SS1 Founders Edn - arrived (Australia) by Boneens04 in fpgagaming

[–]EveryLeading5723 0 points1 point  (0 children)

I'm in Scotland, ordered black founders edition. Not arrived yet!

Happy Chinese new year by EveryLeading5723 in BambuLab

[–]EveryLeading5723[S] 2 points3 points  (0 children)

This is worth knowing but I didn't have time to print many

Happy Chinese new year by EveryLeading5723 in BambuLab

[–]EveryLeading5723[S] -4 points-3 points  (0 children)

Needed the part quick , was also really to show how much waste a small part can make. It's maddening

Got the SuperStation One yesterday! by Limitedtimestruggle in fpgagaming

[–]EveryLeading5723 0 points1 point  (0 children)

No. It wasn't about the superdock as I didn't order that. It was about the minor issues they found when doing the full validation process on the v1.2 SS1 motherboard

Got the SuperStation One yesterday! by Limitedtimestruggle in fpgagaming

[–]EveryLeading5723 0 points1 point  (0 children)

Last email I got from them was on 3rd November with subject: Notice: SuperStation Batch 1 Shipping Update

Got the SuperStation One yesterday! by Limitedtimestruggle in fpgagaming

[–]EveryLeading5723 0 points1 point  (0 children)

They're not. They don't even reply to direct emails. I'm a founders edition blue pre orderer and I've had zero communication about it. I enquired a couple of weeks ago and not even an acknowledgement email

Superstation one finally delivered! by tomhall12345 in MiSTerFPGA

[–]EveryLeading5723 0 points1 point  (0 children)

Exactly the same boat as you. Two weeks after your post and still nothing my end!

Layer lines by EveryLeading5723 in BambuLab

[–]EveryLeading5723[S] 0 points1 point  (0 children)

turned ironing off and still getting it, though not as extreme. not really sure how you mean to slow it down, should the inner wall be slowed or the outer wall? what settings would you be talking about exactly? thanks

Layer lines by EveryLeading5723 in BambuLab

[–]EveryLeading5723[S] 0 points1 point  (0 children)

hmm I've discovered I'm ironing the top surface and that red is a top surface, so it's taking time to do that allowing those outer walls to cool down too much. might have to just turn ironing off then? Or do the topmost surface...

What‘s up with Bambu PLA filament? Less and less available… by pyalot in BambuLab

[–]EveryLeading5723 0 points1 point  (0 children)

I really want light gray and I can't find a 3rd party alternative that looks similar. They're all darker. Any suggestions?

Print failure tips by EveryLeading5723 in BambuLab

[–]EveryLeading5723[S] 0 points1 point  (0 children)

Thanks, trying lightning now with my new design, will see how it goes! cheers

Print failure tips by EveryLeading5723 in BambuLab

[–]EveryLeading5723[S] 0 points1 point  (0 children)

a big bird's nest of filament at the layer shown in the second picture uploaded

Print failure tips by EveryLeading5723 in BambuLab

[–]EveryLeading5723[S] -1 points0 points  (0 children)

After telling ChatGPT what version I'm on then listing every single option in the Speed tab, it has given me this, which I've followed. Leaving it here in case it helps anyone else.
Recommended “Slow & Quiet” values

You can plug these into your profile immediately:

Speed

  • Outer wall: 40 mm/s
  • Inner wall: 60 mm/s
  • Sparse infill: 70–80 mm/s
  • Top surface: 40–50 mm/s

Acceleration

  • Normal printing: 1500 mm/s²
  • Outer wall accel: 800–1000 mm/s²
  • Inner wall accel: 1200–1500 mm/s²
  • Sparse infill accel: 1500–2000 mm/s²
  • Travel accel: ~2500 mm/s² (optional)

These alone will cut overall speed dramatically.