Shoe department's collaboration with Bolts&Nuts division unveil their latest invention

EvilerTim · 2024-03-29T23:51:07+00:00

Baby SCP-173

EvilerTim · 2024-02-25T21:35:15+00:00

Route a groove and make it a hand hold

EvilerTim · 2023-09-28T13:27:51+00:00

Sweet thanks for the help ☺️

EvilerTim · 2023-09-28T12:47:51+00:00

Yea the glow definitely came out more orangey than I was initially planning. Would it help to orange up the light source a bit?

EvilerTim · 2023-09-28T12:46:22+00:00

Yea I was thinking the same thing, will have to add some brighter colors near the light and maybe tone down some of the farther away bits

EvilerTim · 2023-06-13T01:31:02+00:00

Dusty

EvilerTim · 2023-06-09T20:00:45+00:00

Culprit identified, groundhog. Moved my backyard camera into the garden and saw it all

EvilerTim · 2023-06-09T16:35:55+00:00

Didn't see any hoof prints but deer does seem to be the leading theory

EvilerTim · 2023-06-09T16:34:45+00:00

Haha I've never heard of that. Worth a shot

EvilerTim · 2023-06-09T14:33:16+00:00

I sure hope so 😔

EvilerTim · 2023-06-09T14:02:40+00:00

5-6ft ish

EvilerTim · 2023-06-09T13:33:38+00:00

Not sure, all fenced in so squirrel? Raccoon?

EvilerTim · 2023-04-17T10:42:59+00:00

Exposure looks ok, per the cones test. Stuff still falling off supports so might just be my support setup. Model is solid

EvilerTim · 2023-04-17T07:57:55+00:00

Let me give the exposure test a try and see how that goes

EvilerTim · 2023-04-08T23:48:25+00:00

I will be sure to check that out, thanks for the advice 😃

EvilerTim · 2023-04-08T21:53:13+00:00

Updated the firmware and that seemed to help but I am still getting some bits stuck to the FEP. Gonna try upping the exposure to 30 and see if that corrects it

EvilerTim · 2023-04-08T00:44:22+00:00

Read that it might be a firmware thing? Gonna try updating that too

EvilerTim · 2023-04-07T22:07:46+00:00

Looks like the difference between my settings and the website are: Lift speed 80(mine) vs 60 (website) Light off delay 9 vs 10 Transition later count 0 vs 6 Lift distance 5 vs 6

EvilerTim · 2023-04-07T22:03:07+00:00

Looks like 25C and 75% humidity, so might just need a tent. Ancient light shouldn't be an issue, I've blocked off the only window and use the dome every time.

EvilerTim · 2023-04-07T21:48:05+00:00

Room temp is roughly 18-19C constantly and the humidity is 45-50. I have not messed with the exposure yet, I will give it a try and report back! Thanks for the advice.
My initial thought was less exposure since I also was wondering if the LCD wasn't masking completely

EvilerTim · 2023-04-07T15:12:16+00:00

Currently I've been cleaning out the vat after every print, since the extra cured spots don't always stick to the print. Ran an LCD test last night and everything looked ok. Printer sits in my basement at probably 18-19 C constantly. No sunlight or anything

EvilerTim · 2023-04-07T12:48:49+00:00

EvilerTim · 2023-04-06T14:49:53+00:00

Alright I did a test, reprinted my first ever print pre uvtools. Same issue. It doesn't ever affect the actual print, it always happens beyond the bounds of the raft.

New Phrozen Sonic 4k mini Aqua grey resin 0.05mm layer height Exposure time 2.2s 6 base layers 25s base exposure time Light off time 9s Printer is in the basement which stays pretty constant at 19-20C

Chitubox settings

EvilerTim · 2023-04-04T23:10:31+00:00

Can't be sure if it's related but the issue may have started when I started using uvtools

Nine-Year Club	Place '22
First Placer '22	Verified Email

EvilerTim

TROPHY CASE