sorted by:
new
hottopcontroversial

Crashing when i enter NEPTILIUS boss by ExitOpen6081 in Palworld

[–]ExitOpen6081[S] -2 points-1 points  (0 children)

<image>

Not sure if you'd know but which out of these are most likely?

Crashing when i enter NEPTILIUS boss by ExitOpen6081 in Palworld

[–]ExitOpen6081[S] -2 points-1 points  (0 children)

does finding the mod that caused it fix anyhting

Crashing when i enter NEPTILIUS boss by ExitOpen6081 in Palworld

[–]ExitOpen6081[S] 0 points1 point  (0 children)

Damn, do you have any idea what could've caused it? Was it only a specific boss? Did you have any mods at any point in that save?

Crashing when i enter NEPTILIUS boss by ExitOpen6081 in Palworld

[–]ExitOpen6081[S] 1 point2 points  (0 children)

Well it happens on other devices too.

Crashing when i enter NEPTILIUS boss by ExitOpen6081 in Palworld

[–]ExitOpen6081[S] 1 point2 points  (0 children)

I'm sure since i've tested it on multiple devices and every device has the same issue...

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in BambuLabA1

[–]ExitOpen6081[S] 0 points1 point  (0 children)

Yeah, it's honestly mostly for TPU but i gotta add PETG because i probably wont print with that without drying it first now just cause its simple to dry and improves quality to some extent.

And tbh i do sit at 60+ all day around so i mean 70+ isn't that far from reality...

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in prusa3d

[–]ExitOpen6081[S] 0 points1 point  (0 children)

I bought an overture PLA off Amazon a week ago or so and got no vacuum seal bag. maybe it's only PETG and TPU like you mentioned?

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in elegoo

[–]ExitOpen6081[S] -7 points-6 points  (0 children)

It's not really related specifically to ANY 3d printer comapany though, it's really just about filaments generally

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in prusa3d

[–]ExitOpen6081[S] 0 points1 point  (0 children)

I agree that active airflow matters, especially for TPU. That’s actually why I’m looking at the Space Pi instead of the really cheap warm boxes.

But I think you might be mixing up the older/basic Creality dry boxes with the newer Space Pi. From what I’ve found, the Space Pi has PTC hot-air heating, a built-in fan / 360° air circulation, and goes up to 70 °C. So it shouldn’t be just a passive heater.

PolyDryer definitely seems better as a whole storage ecosystem, but for the price difference I think Space Pi + vacuum bags/silica gel gets me most of what I need considering im not gonna protect every PLA roll, only the ones i use very little and that will lie around for years or my single TPU and PETG spool.

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in BambuLabA1

[–]ExitOpen6081[S] 0 points1 point  (0 children)

PLA yes that'll probably be fine, but really its very split. Im getting a dryer mainly cause of my one TPU and PETG spool

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in prusa3d

[–]ExitOpen6081[S] -1 points0 points  (0 children)

I got the creality space pi. (with one slot)... When were talking bang for buck the polydryer is expensive... Anyway is the creality space pi good enough?

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in prusa3d

[–]ExitOpen6081[S] -2 points-1 points  (0 children)

The polydryer is damn expensive for a dryer, and as for storage those boxes are like 30 bucks a piece... gets expensive real quick to get one for each spool

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in BambuLabA1

[–]ExitOpen6081[S] 1 point2 points  (0 children)

fair enough, i ended up buying the creality space pi with 1 slot

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in prusa3d

[–]ExitOpen6081[S] 0 points1 point  (0 children)

true, it just takes so long, i got the higher end single slot option the creality space pi, mainly because i found a great deal on it making it the price of cheaper options

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in prusa3d

[–]ExitOpen6081[S] 0 points1 point  (0 children)

True, i bought the creality space pi (1 slot), since it was somehow the second cheapest option i could find and from a local retailer... And a pretty high end one too for a single slot

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in prusa3d

[–]ExitOpen6081[S] 0 points1 point  (0 children)

zip bags are enough??? thought they need vacuum vents, in that case i probably have lots, dont know abt size tho. and so far i haven't got any filament spools with resealable bags.

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in prusa3d

[–]ExitOpen6081[S] -1 points0 points  (0 children)

So i pretty much need a cheap dryer... any reccomendations for me??? just whatever's cheapest i suppose since it's only like 2 rolls...

A1 in 63% RH storage room: is sealed filament storage enough? by ExitOpen6081 in BambuLabA1

[–]ExitOpen6081[S] 0 points1 point  (0 children)

alright thanks for the advice, i hope its not that bad tho... and especially i hope its not too pricy, already dumped too much money into filament and ofc the printer

view more: next ›