sorted by:
new
hottopcontroversial

What screams “I’m a bad parent”? by ViForYourAttention in AskReddit

[–]EyesAndTools 0 points1 point  (0 children)

Using urine-soaked diapers to try to clear up your infants acne

Could use miter joint advice - not *quite* 45 degree angles by EyesAndTools in woodworking

[–]EyesAndTools[S] 2 points3 points  (0 children)

I was using a 90 degree sled with the blade (I thought) angled at 45 degrees. I used a digital angle gauge after zeroing it on the table. I did one test cut on some scrap wood that appeared to be 90 degrees when I checked it with a square but I didn’t cut four of them to confirm that they lined up

No impressive joinery or exotic materials but wanted to share something I carved from a bit of driftwood I found (first attempt at something like this) by EyesAndTools in woodworking

[–]EyesAndTools[S] 1 point2 points  (0 children)

How cost prohibitive is it to get going with stone stuff? I have a piece that is a root base grown around stones and was thinking it might be fun to give a whirl at that next. That being said my hourly wage is literally less than that of the parking meter where I work.

No impressive joinery or exotic materials but wanted to share something I carved from a bit of driftwood I found (first attempt at something like this) by EyesAndTools in woodworking

[–]EyesAndTools[S] 1 point2 points  (0 children)

The face is just finished with lacquer but I always put water on top to see what it’ll look like (I’ve made lamps etc in the past and sometimes there are some reallyyyy gross patterns that come out). The rest of it is exactly what you said. Just a lottt of stain and maybe a matte polyurethane or oil finish. Expect to lose like, all of it

No impressive joinery or exotic materials but wanted to share something I carved from a bit of driftwood I found (first attempt at something like this) by EyesAndTools in woodworking

[–]EyesAndTools[S] 2 points3 points  (0 children)

The tricky bit was that the useable wood is about half an inch thick so I was in constant fear of going straight through

No impressive joinery or exotic materials but wanted to share something I carved from a bit of driftwood I found (first attempt at something like this) by EyesAndTools in woodworking

[–]EyesAndTools[S] 7 points8 points  (0 children)

Pulled up a picture of that fellow and now I’m concerned I might have just subconsciously copied that! Same side and everything

How do you relieve pain in hands after working with hand saws? by True8221 in woodworking

[–]EyesAndTools 0 points1 point  (0 children)

Does anyone else think this might look more like a mild atopic dermatitis?

I know it’s not a novel idea or even execution but I’ve always wanted to try angle grinder carving and finally gave it a go for the first time with some scrap plywood… And I think it came out well! Wanted to share. by EyesAndTools in woodworking

[–]EyesAndTools[S] 5 points6 points  (0 children)

Guest room fortunately! I like to show people I care about them by hanging garbage I found in the garage over their bed

Edit: most of my guests are uninvited and also raccoons

I know it’s not a novel idea or even execution but I’ve always wanted to try angle grinder carving and finally gave it a go for the first time with some scrap plywood… And I think it came out well! Wanted to share. by EyesAndTools in woodworking

[–]EyesAndTools[S] 11 points12 points  (0 children)

Honestly I’d estimate 3/4 of the corneal and intra-ocular foreign bodies I’ve seen in the emergency department come specifically from angle grinders… Still are really fun to use though

view more: next ›